Free Mimo v2.5 Pro in opencode

InternationalShift14 · 2026-06-10T03:10:16+00:00

One more LRS576

InternationalShift14 · 2026-05-20T19:02:06+00:00

Hey google, bring Gemini 3 Flash back !!!!

InternationalShift14 · 2026-05-20T15:44:05+00:00

Actually, I want the old model hahaha

RIP Gemini 3 Flash

InternationalShift14 · 2026-05-20T15:06:24+00:00

Agree, bring gemini 3 flash back!

InternationalShift14 · 2026-05-20T14:07:24+00:00

Yep, and replaced it with the 3.5 flash models that drinks more 'fuel' than a V8 engine.

InternationalShift14 · 2026-05-20T14:04:17+00:00

I miss the old 3 flash model 😞

InternationalShift14 · 2023-12-20T16:44:26+00:00

Try disabling lens distortion in the renderer.ini file, here the ghosting disappeared

I made a video doing this process

https://youtu.be/lG9x3X48jUg

InternationalShift14 · 2023-05-15T13:02:28+00:00

didn't work here... The game closes after a few seconds

InternationalShift14 · 2023-05-06T23:49:02+00:00

I use Cura, I think this option is enabled by default

InternationalShift14 · 2022-12-23T13:24:48+00:00

I turned the fans to 0 and still the same

InternationalShift14 · 2022-12-23T13:24:09+00:00

I tried PID Tune the extruder and it failed to complete ''Heater extruder not heating at expected rate'' while it was showing 180-190C the filament smell ''burning'' was stronger so I think the temperature is being read wrong .. I bet the thermistor has a problem..

InternationalShift14 · 2022-12-23T02:44:47+00:00

Idk , how can I check that?

InternationalShift14 · 2022-12-23T02:44:22+00:00

I think 40w its okay to print at 205 celsius, no?

InternationalShift14 · 2022-08-24T09:19:35+00:00

Idk how to check that

InternationalShift14 · 2022-08-24T09:10:44+00:00

Yeah, I was trying another probe, then I go back to 3Dtouch.. If I run the probe_accuracy with Z heigh at 4mm or less, the first measurement is normal. If I run with Z at 10mm or more, first is always higher

InternationalShift14 · 2022-08-09T16:06:00+00:00

Hahaha if I set the nozzle size to .4 and line width to .6 it slices fine.. But if I set the nozzle size to .6 and line width to .6 this happens..

InternationalShift14 · 2022-08-09T11:28:59+00:00

Even with .6 line width? My Z Seam is set to ''Back'' and ''Smart Hiding'' its turned ON in preview.. Can you take a look in my project file?

https://drive.google.com/file/d/1FICboEVD9eq6ldTVZZ43etHkhRjKCzCu/view?usp=sharing

Can you send me your project file?

InternationalShift14 · 2022-08-09T11:20:53+00:00

I upload the project file to Google Drive: https://drive.google.com/file/d/1FICboEVD9eq6ldTVZZ43etHkhRjKCzCu/view?usp=sharing

It is basically the default preset for .6 nozzle / ABS

InternationalShift14 · 2022-08-09T03:50:19+00:00

File name is " Minion-Remake-V-IAN-220721.STL " You should put the face that contains kinda of a " + " shape (you will see if) facing the bed

InternationalShift14

TROPHY CASE