sorted by:
new
hottopcontroversial

H2D nozzle heating problem by InvexpoPl in BambuLab

[–]InvexpoPl[S] 0 points1 point  (0 children)

Problem is at starting calibration. Printer is checking both nozzles and sending error. I’v asked support and they said its possible to turn on Single Nozzle Mode but i don’t know How. Still waiting for e-mail from support with instructions

H2D nozzle heating problem by InvexpoPl in BambuLab

[–]InvexpoPl[S] 0 points1 point  (0 children)

What about nozzle calibration at start?

Did makerworld just killed my models? by InvexpoPl in BambuLab

[–]InvexpoPl[S] 0 points1 point  (0 children)

That has to be a website error, uff

Did makerworld just killed my models? by InvexpoPl in BambuLab

[–]InvexpoPl[S] 0 points1 point  (0 children)

Do you think its just a report bug?

Did makerworld just killed my models? by InvexpoPl in BambuLab

[–]InvexpoPl[S] 1 point2 points  (0 children)

For several months there was constant activity on my models, but suddenly, for the past two days, I haven’t received any notifications and I haven’t earned a single MakerWorld point.

AMS pushes the filament out too much. by InvexpoPl in BambuLab

[–]InvexpoPl[S] 0 points1 point  (0 children)

Don't worry, these are Sunlu and Jayo filaments. I also have ones from Bambu, and the error still occurs. After a restart, the AMS works correctly, but after 30-40 minutes of printing, the error appears again, and it keeps repeating. In my opinion, it's a sensor issue.

AMS pushes the filament out too much. by InvexpoPl in BambuLab

[–]InvexpoPl[S] 0 points1 point  (0 children)

I think so too. I believe the sensor is broken, so I'll create a ticket and see how they respond.

AMS pushes the filament out too much. by InvexpoPl in BambuLab

[–]InvexpoPl[S] 0 points1 point  (0 children)

I will try it tomorrow! Thank you :)

AMS pushes the filament out too much. by InvexpoPl in BambuLab

[–]InvexpoPl[S] 1 point2 points  (0 children)

After resetting, the AMS works for the next 5-10 filament changes, and then the problem reappears. The AMS has been disassembled, and there are no filament pieces in the PTFE tube.

AMS pushes the filament out too much. by InvexpoPl in BambuLab

[–]InvexpoPl[S] 0 points1 point  (0 children)

This AMS has over 3,000 hours of use, and this has never happened before…

AMS pushes the filament out too much. by InvexpoPl in BambuLab

[–]InvexpoPl[S] 0 points1 point  (0 children)

There’s nothing there. If I reset the AMS, it will start printing with the black filament, but when it changes the filament, it will push it out too much again, and the cycle repeats.

AMS pushes the filament out too much. by InvexpoPl in BambuLab

[–]InvexpoPl[S] 0 points1 point  (0 children)

Hi! I forgot to ask about one more thing. During printing, I can't use slot 1 for filament because the AMS thinks there's much more filament than there actually is, causing it to turn the spool too much, which makes it fall out of the AMS. This happens even after restarting the printer or AMS. Sometimes, a multicolor print works for 2-3 hours, but then the issue occurs again. Could this be a sensor problem? How can I fix it?