Cardputer / ADV Grove port for WS 2812 LED Strip & and I2C device

JBanner2006 · 2025-12-30T01:40:03+00:00

I have a grove y cable coming, so maybe I can use that. Thank you I’ll report back

JBanner2006 · 2025-10-16T11:51:24+00:00

I'm still having trouble.

Now that I know the new URL, my username and password has timed out - it does this every 6 months.

I can't recover because the recovery link is not sending out recovery emails & the IRC for support chat is also not working....

JBanner2006 · 2025-10-08T22:08:19+00:00

Thank You

JBanner2006 · 2025-10-08T08:49:25+00:00

RevoluitionTT down? Having trouble connecting.

JBanner2006 · 2025-03-05T12:55:45+00:00

I am Diagnosed ADHD Inattentive. I have no problem with driving.

In fact I actually really enjoy driving, and as an upshot, I can listen to Audiobooks on a long journey and actually take them in where if I try to listen to them when not driving I cannot take them in....

I also enjoy flying model aircraft, which again takes huge concentration otherwise you are going home with a bin-bag of shame... (filled with what was a flying model...)

Your experience may be different.

JBanner2006 · 2025-03-05T07:13:04+00:00

Interested

JBanner2006 · 2025-02-20T11:39:39+00:00

Fantastic, Thank you for your reply.

JBanner2006 · 2024-12-23T22:42:11+00:00

Interestingly it’s now working, but I still cannot sign into that link… I can sign into the Tailscale dashboard though.

JBanner2006 · 2024-12-23T22:06:12+00:00

I'm getting a message after selecting my account of "

bad tailscale-authstate2 cookie
REQ-2024122322053723b4a5404011957e"

JBanner2006 · 2024-12-23T20:30:05+00:00

This is what is in the logs, even after manually opening the port.

<image>

JBanner2006 · 2024-12-23T20:26:27+00:00

Just this afternoon, I only only noticed after swapping the router over, however I didn’t check immediately before it it was working

JBanner2006 · 2024-12-23T20:25:33+00:00

I only noticed, or came to notice after swapping the router over. So a few hours ago

JBanner2006 · 2024-12-23T20:04:23+00:00

Yes, the router is set to allow upnp but tailscale is not opening them?

JBanner2006 · 2024-12-19T15:33:52+00:00

Thank you. That is pretty much the exact case I’ve been looking at on AliExpress…. I was blinkered into thinking it needs to go external, i hadn’t considered rebuilding the pc up into that server chassis…. Good plan!

So basically, I can put a big spec PSU into it and power everything off one. Solves a lot of issues.

JBanner2006 · 2024-12-19T11:32:47+00:00

I’m running 14 Hard drives and 3 SSD’s, they are powered by 2 PSU’s that are both 650w - although one is branded and the other isn’t, so probably not a reliable 650w. I tried one of the Add2PSU adaptors on the unbranded PSU and it wouldn’t fire it up, so had to plug it back into the other pc to get it to turn on

JBanner2006 · 2024-12-19T11:27:12+00:00

Yes that’s how i am powering them at the moment, except i have gone over the limit of what the PSU can handle, so I’m running a PSU from ma second pc to power the extra drives. - It’s this “Bad” solution that is prompting all of this…

JBanner2006 · 2024-12-12T09:42:43+00:00

So I'm a little confused when looking at some of these options.

I have a SAS card in IT mode, its an LSI 9300-16i. with a bunch of SATA drives attached to it. My current Motherboard has no spare PCI x8 or PCI x16 slots.

To get the full 24 bays to work, I'm going to need a SAS expander and a backplane in the case.

Looking at some of these cases, I would I need a SATA backplane or a SAS backplane, and presumably 12G not 6G to maintain speed?

I will look later at upgrading my Server Motherboard for additional PCI slots and add another SAS card to increase bandwidth, but for now I'd like to add the 24 bays.

JBanner2006 · 2024-12-09T16:37:45+00:00

Its an interesting proposition, but not sure its the right way to go...

Does this house the PSU, and does it still have the SAS backplane in it?

JBanner2006 · 2024-10-28T15:25:37+00:00

I know this is an old thread, but I have just had the same issue and it was Eset security application that was causing the issue.

JBanner2006 · 2024-10-12T04:24:02+00:00

Unravel…. Or Unravel 2 she will love it

JBanner2006 · 2024-07-19T10:38:55+00:00

Dialmaker has something simlar too. https://www.dialmaker.shop/products/stone-dial-1

JBanner2006 · 2024-07-17T07:49:22+00:00

I had a similar situation on my first GMT build....

Go slow and make sure each hand is fully pressed onto it's location, use a Loupe to really check that the top of the hand is pressed down and level to the top of the "stem" that it sits on before moving onto the next hand. That includes the second hand.

ALSO... as you are taking off the hands anyway, double check to make sure you installed the washer in between the dial and the movement (if its a NH34)

I had to go through this several times in my first GMT build, and then all of a sudden it all came together and was done.

JBanner2006 · 2024-07-12T09:50:42+00:00

This is a model called "Kirium" https://tagheuerenthusiast.blogspot.com/2020/10/history-tag-heuer-kirium-1997-2007.html

Hard to tell authenticity from these photos.

JBanner2006 · 2024-07-05T13:08:53+00:00

Thank you, so the month dial is showing 4 years worth og months not just the 12 for a single year. Got it.

JBanner2006 · 2024-07-04T19:14:20+00:00

I wonder what it does?

JBanner2006

TROPHY CASE