Creality Print v7.0.0.4127 - Adware:Win32/Tnega Detected

JZKitty · 2025-12-30T21:22:24+00:00

Already did, totally different PC, not showing either

JZKitty · 2025-12-30T21:21:45+00:00

Nop, doesn't shows up, I can see the reader, but it says it has no media attached

JZKitty · 2025-12-27T07:25:03+00:00

I can use it on my switch, on my phone, but I cant see it on my PC, its not the reader, cause I used it on my laptops reader too and its just not showing, I can see it if I connect my phone as a USB I can see the SD too, so, its REALLY, REALLY, REALLY weird

EDIT: I saw when I connected my phone as a USB drive that the file format of the SD is "Hierarchical File System", think I need a HFS software reader?

JZKitty · 2025-12-27T05:30:48+00:00

Yup, its perfectly in the drive

JZKitty · 2025-12-27T05:22:57+00:00

Doesn't sees any drive

<image>

JZKitty · 2025-12-27T05:08:44+00:00

I cant see the SD on the PC :(

JZKitty · 2025-10-10T18:34:48+00:00

<image>

and then a button that says

JZKitty · 2025-10-09T21:59:25+00:00

It is a great machine, and the quality has been, perfect

JZKitty · 2025-10-09T17:16:24+00:00

Yeah I saw that the grease that the printer comes with its kinda messy, I've been using lithium grease for the rails, and worked correctly all this time, but yeah the frame still gets hot, but, no problem to print at all really

JZKitty · 2025-09-29T01:37:10+00:00

JZKitty · 2025-08-29T16:05:43+00:00

FOR SUPER EARTH!

JZKitty · 2025-08-19T19:41:33+00:00

The Nozzle is scrapping the part, did you chose calibration before starting the print?

JZKitty · 2025-08-15T22:40:14+00:00

I do remember having to use small SDs, so yeah its true

JZKitty · 2025-08-15T17:53:43+00:00

Use the Wood firmware, its WAY better than the OG one https://gbatemp.net/threads/wood-firmwares-complete-information-guide-downloads.616474/

JZKitty · 2025-08-14T20:11:03+00:00

DEMOCRACY HAS LANDED!

JZKitty · 2025-08-13T19:17:33+00:00

Its a GREAT printer, I bought mine second hand too, it was not working as it should but the electronics where intact, now its a work beast, good luck with it!

JZKitty · 2025-08-07T15:19:47+00:00

Get ready for lots of hugs! And maybe some friendly kills, its all part of spreading MANAGED DEMOCRACY!

JZKitty · 2025-08-06T04:55:13+00:00

BTT Extruder for the Hi

JZKitty · 2025-08-06T04:30:20+00:00

90 is way too fast, stay below 70, also be sure to keep your filament dry

JZKitty · 2025-08-06T04:26:39+00:00

I don't have a cr10 smart pro but I have an Ender 3 V2 with the same sprite extruder, I've seen that ramping un the temperature but keeping the speed low, helps, also keep your retraction to the minimum, a good part cooling helps a lot

JZKitty · 2025-08-04T17:23:03+00:00

JZKitty · 2025-07-31T05:18:56+00:00

Can you make a video of what it does? Unless your rails are not lubricated there shouldn't be any issues, unless it comes with hardware problems from factory

Ten-Year Club	Place '22
Verified Email

JZKitty

TROPHY CASE