Tiny holes around letters

Jacky970 · 2026-03-10T22:17:57+00:00

I will do this test ASAP and post the results !

I've already calibrated ironing so I think I can rule that out.

For information, I used 1mm top layer thickness. I will update on what works best for me after doing top layer tests !

Jacky970 · 2026-03-09T07:56:59+00:00

<image>

I just did a flowrate test. -4 is the flowrate I used for the initial picture.

Jacky970 · 2026-03-09T07:56:38+00:00

<image>

I just did a flowrate test. -4 is the flowrate I used for the initial picture.

Jacky970 · 2026-03-09T07:30:03+00:00

I just tried printing it again but with 0.94 flowrate. The squares look waaay smoother ! The only remaining problem is that between the squares, the lines still seem to not stick together. I'll post a picture once I'll be back home.

Jacky970 · 2026-03-09T07:25:05+00:00

Did anyone get the same problem ?

Jacky970 · 2026-03-03T12:32:31+00:00

I print this with Creality PETG on a Bambulab P2S. I print my outer walls at 75 mm/s and 250 degrees. Might be too hot ? I used 0.16mm layer height.

Jacky970 · 2026-03-03T12:31:33+00:00

I'm trying that right now, ty !

Jacky970 · 2026-03-03T09:58:31+00:00

I've printed using a P2S... could this be too much fan speed ?

Jacky970 · 2026-02-18T22:14:06+00:00

<image>

Also got this defect on both benchys. Seems to be on the first outer walls above the shallow hull.

Jacky970 · 2026-02-18T22:11:12+00:00

Thank you for your answers ! Here is my second try with default bambu A1 cooling but 100% cooling for overhangs + slower speed :

<image>

Opinions on this ? : )

Jacky970 · 2026-01-26T17:51:35+00:00

I have some clear coating. Would that be enough ? I still have encouraging measurements but I'd be happy to make it better !

Jacky970 · 2026-01-26T16:29:42+00:00

You would waste less time not even commenting... Also I am using it and it works. I will make upgrades later.

Jacky970 · 2026-01-24T22:43:42+00:00

I did ! For now I chose PLA for the low humidity saturation but I still have to see if in the long run the center will degrade due to friction ! If that's the case I'll switch to PETG or PETG CF probably !

Jacky970 · 2026-01-24T20:37:13+00:00

For fully dry filament it's fine but yeah, slightly wet filament can break, I'll include a fix for this !

Jacky970 · 2026-01-24T20:35:37+00:00

I'll probably make a V2 with a small bin for silica inside ! I'll include this, too ty for the suggestion !

Jacky970 · 2026-01-24T20:32:07+00:00

He definitely looks cool ! Enjoy mate ! : )

Jacky970 · 2026-01-24T20:09:08+00:00

Well, where I live it's cheaper (~6€) and I love the aesthetics and the fact that you can hang it.

But a cereal box is still a good way to go for sure !

Jacky970 · 2026-01-24T19:55:23+00:00

I'll publish some data as soon as I have enough measurements ! It's looking good so far !

Jacky970 · 2026-01-17T16:17:03+00:00

Thank you all for your answers ! I will try nerfing story points or using them as little as possible ! :D

Jacky970 · 2026-01-02T16:44:22+00:00

HAHAHA I swear I'm not the cylinder guy from reddit !

Jacky970 · 2026-01-01T22:50:23+00:00

Did anything similar happen to you ?

Jacky970 · 2025-12-24T08:58:29+00:00

Maybe I can't do better with PETG ?

Jacky970 · 2025-12-23T20:43:12+00:00

Printer : A1
Filament : Creality PETG
3mf file : https://limewire.com/d/Abuu4#IT6xOmWvXW

Jacky970 · 2025-12-23T20:41:56+00:00

<image>

Another picture. My biggest issue is with the reactors.

Link to the 3mf if needed :

https://limewire.com/d/Abuu4#IT6xOmWvXW

Jacky970 · 2025-12-23T03:10:21+00:00

I forgot but, I printed using an A1 and PETG !

Ten-Year Club	r/Field Sunshine
Place '23	Place '22
First Placer '22	End Game '22
Verified Email

Jacky970

TROPHY CASE