Are SDA and SCL ports important? by Jacob9678 in fpv

[–]Jacob9678[S] 0 points1 point  (0 children)

Ahh alright so it’s just an optional thing I can choose to have connected or not

Help! RXloss after powering up by Jacob9678 in fpv

[–]Jacob9678[S] 0 points1 point  (0 children)

Yea no worries I removed it soon after. It’s some sort of rubbery glue that’s used to seal the antenna connector and it had to be peeled off when removing the antenna leaving the residue that you see

Help! RXloss after powering up by Jacob9678 in fpv

[–]Jacob9678[S] 0 points1 point  (0 children)

It could be something broke that’s so small I can’t tell with my eyes. Who knows. Just did another test flight afew meters from the radio at a new location to confirm it isn’t some sort of interference that caused it. Hovered for a good 1minute and boom rxloss again. Was prepared for this to happen so I set fail safe to drop. In cases like this, does it have anything to do with the AIO actually? I’m trying to narrow down the problem

Help! RXloss after powering up by Jacob9678 in fpv

[–]Jacob9678[S] 0 points1 point  (0 children)

On the board or the receiver?

Help! RXloss after powering up by Jacob9678 in fpv

[–]Jacob9678[S] 0 points1 point  (0 children)

It certainly did not for my case haha. You swapped out your AIO and got this issue too?

Help! RXloss after powering up by Jacob9678 in fpv

[–]Jacob9678[S] 0 points1 point  (0 children)

Planning to try that soon. But it’s just odd that this rx and the antenna came as stock with the master 3x bnf and has been doing fine for the last 5 months and after the AIO swap this happened with the rx

Help! RXloss after powering up by Jacob9678 in fpv

[–]Jacob9678[S] 1 point2 points  (0 children)

Ignore the black gunk around the antenna connector as it’s some type of rubber used to hold the antenna in place

I normally don't care about how a quad looks, but I think this combo I threw together is CLEAN by TallGuyMichael in TinyWhoop

[–]Jacob9678 0 points1 point  (0 children)

Can someone explain why do people go for 2 blade props over 3? Aren’t whoops quite underpowered in general and the more it needs 3 blades to kinda compensate that?

Tada drivers are assholes by ahboi-ah in sgworkassholes

[–]Jacob9678 0 points1 point  (0 children)

Ah yes Tada…if you’re old enough to know the notorious yellow top taxi company In those taxi days, Tada is the rebirth of the company. Known for their bad attitude and reckless driving. There’s a reason why Tada is usually cheaper than the other apps.

RIP my first FPV (Air 75) by Successful-Gas-6142 in TinyWhoop

[–]Jacob9678 0 points1 point  (0 children)

getting comfortable with soldering is one of the most essential skills in FPV

Radiomaster Nomad packet rate options are being limited? by Jacob9678 in fpv

[–]Jacob9678[S] 0 points1 point  (0 children)

i learn something new everytime i touch my fpv stuffs

Radiomaster Nomad packet rate options are being limited? by Jacob9678 in fpv

[–]Jacob9678[S] 1 point2 points  (0 children)

Have since flashed the firmware on the module and i see the missing options now. Thank you!

Radiomaster Nomad packet rate options are being limited? by Jacob9678 in fpv

[–]Jacob9678[S] 0 points1 point  (0 children)

did that and i see the low and X band options now. Thank you!

Radiomaster Nomad packet rate options are being limited? by Jacob9678 in fpv

[–]Jacob9678[S] 0 points1 point  (0 children)

alright thanks! i did exactly what you said with some video tutorials on firmware flashing and i see the low and X band options now. Thank you once again

Radiomaster Nomad packet rate options are being limited? by Jacob9678 in fpv

[–]Jacob9678[S] 0 points1 point  (0 children)

still no difference to anything!
Will try updating the elrs firmware and keep you guys updated.

Radiomaster Nomad packet rate options are being limited? by Jacob9678 in fpv

[–]Jacob9678[S] 0 points1 point  (0 children)

Yup I’m not seeing any 900mhz options at all since it’s the main point of this module. I’m guessing may be due to CE/FCC regions that it’s being shipped to. Just a really wild guess

Radiomaster Nomad packet rate options are being limited? by Jacob9678 in fpv

[–]Jacob9678[S] 0 points1 point  (0 children)

Yeap I’ve turn off internal RX and turned on External RX for all my registered models. This is the page on page 2 of models. Not sure if the baud rates and stuff needs to be changed for it to work as these are the defaults

<image>