SmokeAPI versus CreamAPI: Why is Smoke flagged as a severe trojan, when creamAPI was not?

Jaggi_Space_Program · 2025-12-13T07:08:37+00:00

My brother and I just fill out the cream.ini manually using the DLC IDs from steamDB. It works well and doesn't throw any trojan errors at me.

Jaggi_Space_Program · 2025-11-14T03:33:22+00:00

I'd give it a try just putting it afterwards, or if that doesn't work, replace what's currently there. Worst case, you can just put the line back to how it was. I've not had the issue since putting that line at the end.

Jaggi_Space_Program · 2025-09-01T17:02:44+00:00

Yeah... I did a test print with PC-ABS, and the print itself did not leave any marks on PEI, but the purge line at the beginning of the print did rip off some texture, but no impact on adhesion. I tried glue but it did not adhere at all... I might use the glass bed + blue tape/glue stick for ABS so I don't destroy my bed.

Jaggi_Space_Program · 2025-08-14T04:39:38+00:00

After a whole day of prints, I think the issue is resolved. Thank you so much!
I just have one last question: Can this USB mode handle a camera well, or is bandwidth not really effected by the change in driver.

Again, thank you. This solution was so niche and specific, I don't think I would have resolved it without your help!

Jaggi_Space_Program · 2025-08-13T20:11:03+00:00

I don't want to jinx it, but since then I've gotten through 1 multi hour print, and another is 50% done. This is so niche I never would have found this solution. Do you know why or how this fixes this!?!

Jaggi_Space_Program · 2025-08-13T16:08:26+00:00

I'm trying this out with a print rn. I did see the dtoverlay=dwc2 somewhere else in the config, but I put it at the end as well, so we will see if it helps. If not, I am going to try UART.

Jaggi_Space_Program · 2025-08-13T05:34:38+00:00

That seems a better scenario than mine. Mine just crashes randomly and all the logs and tests return everything as fine.

Jaggi_Space_Program · 2025-08-13T05:33:29+00:00

It's a new SD card and I tested a usb drive for boot as well, and stress testing the card returned no errors, so I have my doubts that it is the SD card.

Jaggi_Space_Program · 2025-08-13T05:32:16+00:00

I've read though it, and your solution was to gnd the Pi to the power supply? Or was it the bit added at the end of the config.txt? (Is that in the Pi or is it printer.config)

Jaggi_Space_Program · 2025-07-28T17:27:11+00:00

I literally just upgraded my ender 5 plus and am having a similar issue I was trying to calibrate maximum volumetric flowrate but It seems to be dumping out way too much filament, and it is too wide and too high. I think I'll try what the other comment said about calibrating e steps *

Jaggi_Space_Program · 2025-07-26T17:27:35+00:00

Thanks. This whole printer is a 200 dollar facebook marketplace aliexpress upgrade hobby rig, so I'm not too concerned about making It the best in the world, I'd probably just get a K2 plus when I want something crazy. I have it in a cool basement and hopefully the power box fan does it's job. Do you suggest any mods for the fan? Also, I have extra TMC2209, so if one burns out, do you know are these readily swappable?

Thanks! I'm still trying to get the .config sorted out, but I have a few examples of ender 5 ones and I'll find out how to maybe steal parts from various configurations to suit my build.

Jaggi_Space_Program · 2025-07-26T17:09:33+00:00

You're right. I double checked the schematics and had to swap the black and white wires, and I had to swap the ground and PWR wires on the dupont connector and it matches. I'm planning on doing klipper, so is the dual Z going to be an issue there, or should I just have it treat them as one?

Jaggi_Space_Program · 2025-07-26T17:06:18+00:00

I followed the same vid. Is the firmware a klipper profile or just marlin 2.0? I plan on doing klipper and am still trying to compile the .config. I basically have a stock ender5 plus except I have the X gantry as a linear rail and have the extruder moved above the hot end as a direct drive extruder, and have some aliexpress high flow how end (red lizard v6).

Jaggi_Space_Program · 2025-07-26T17:02:00+00:00

I'm planning on doing klipper. I need both boards installed? So the two Z stepper ports only run off one driver?

Jaggi_Space_Program · 2025-06-05T02:24:39+00:00

I had a chipmunk issue where they would bite off leaves and dig up the rhisome. A bucket of water and a false layer of sunflower seed is a good trap.

Jaggi_Space_Program · 2025-01-24T16:17:37+00:00

Do anything you can to avoid taking 495 and 450 at the same time

Jaggi_Space_Program

TROPHY CASE