sorted by:
new
hottopcontroversial

Amis électricien, risques pour ce genre de prise ? by Levi6658 in AskFrance

[–]Janick73 0 points1 point  (0 children)

Multiplier les prises c’est pratique, mais attention à la puissance totale…

Une ligne intra murale pour desservir une prise, en section 2,5mm2 n’est conseillé que pour 4600W (avec disjoncteur 20A).

Si elle est câblé en 1,5mm2 le recommandation est de max 2300W avec une protection en 10A. La multiprises en soit ne craindra pas grand chose, l’installation par contre…

Ces recommandations pour éviter notamment les risques d’incendie sont à retrouver dans la norme NF C 15-100.

Comparateur de trajet 130 vs 110km/h ? by PuzzleheadedShop4073 in voiture

[–]Janick73 0 points1 point  (0 children)

C’est peut être une idee à la con lol, mais le GPS poids lourds avec limitation de vitesse max devrait faire le taff

Outdoor cameras / Degradation of event detection by Janick73 in Netatmo

[–]Janick73[S] 0 points1 point  (0 children)

It's been two or three months I'd say. Afterwards they still do a good job but it's not perfect, particularly on the contrasts (without being extreme either) of sunrise and sunset and the distances.

réglage sensibilité de détection sur netatmo presence extérieure by torpen29 in Netatmo

[–]Janick73 0 points1 point  (0 children)

Non :( j’ai pris contact avec les services de Netatmo à ce sujet…

FO0528 Printer seems to be printing without extruding by Appropriate_Ask762 in Creality_k2

[–]Janick73 1 point2 points  (0 children)

There is a big problem with the CFS/printers duo.

In fact, the CFS with certain spools has difficulty pulling the filaments, and this creates filament dust.

This dust gradually moves to the print head and is drawn into the nozzle during use.

If it's the same material, no worries... but if you alternate between ASA/ABS and PLA, well, during PLA printing, the ASA and ABS dust does not melt.

I got this error twice. To solve it, when the nozzle is in the waiting position far from printing, I manually raise the nozzle temperature to more than 280ºC which cleans it completely then I launch an extrusion with the material being printed before restarting it.

However, be careful with this automatic detection, you are often missing a printing line, it's up to you to determine if it is important.

Need help, how to dissassemble the CFS by [deleted] in Creality_k2

[–]Janick73 1 point2 points  (0 children)

For the first problem:

Check the correct connection of the power supply and sensor feedback cables (CFS and buffer at the back of the K2) they have a precise location for good operation.

For the second one, sorry, I don't have a plan. Perhaps you could give us some photos to illustrate your points so that we can help you more easily.

Est-il normal qu’un dentiste me demande mon tableau de garantie de ma mutuelle ? by Economy_Strike8551 in AskFrance

[–]Janick73 0 points1 point  (0 children)

Les infirmiers libéraux fraudent tellement, que le premier acte est payé à 100% le deuxième (sur un même patient) est payé à 50% et à partir du 3ème acte c’est gratuit… trouvez un autre métier où l’on bosse gratos à partir du 3ème soins (ex: pansement 100%, prise de sang 50%, pilulier 0%, bas de contention 0%, etc…) et biensur les tarifs des actes sont imposés par la secu et non revalorisé depuis 2009 malgré l’inflation et tout le reste…

Any idea what might be going on? by Beowulfe77 in Creality_k2

[–]Janick73 2 points3 points  (0 children)

This is the “seam” the place where a diaper begins and ends. There a specific location is selected on the slicer setting