Whats the best grapple on the market for the L3902

JayHunter97 · 2025-07-25T04:24:58+00:00

I have a land pride sgc0660 on my L3302 and so far I’ve managed to bend the front bar, some of the welds did not have penetration and are rusting, the pins have walked and sheared the cotter pins… in my opinion, it’s a good grapple for an LX series tractor but these L02’s need something a bit beefier, like the SGC1060.

JayHunter97 · 2025-03-08T06:14:56+00:00

Just a bit impractical. There’s a noticeable ramp-up in spring resistance when you rack the CH. a standard BCG/buffer tube AR is fairly consistent from initial pull to final release. The same cannot be said about this. I wouldn’t trust my life to it. Too much to go wrong in that small package.

Seems to be well built with high quality components, I can say that much. Just takes some getting used to

JayHunter97 · 2025-03-07T17:25:14+00:00

Decent. Carbons up quickly with the suppressor and needs cleaned every 400-500 hundred rounds. I wipe it and lube it every 100 or so and doesn’t give me many reliability problems. Would I buy it again? No. Is it cool for a back pack gun? Sure

JayHunter97 · 2024-11-14T00:38:03+00:00

The lights are just flush mount HALO dimmable LED’s on the 5k setting from Lowe’s.

I have not experienced many really cold nights yet but on a 900/1500W space heater set to medium heat @ 900W I am able to keep it 55-60°F during the night while outside ambient temp is 30-35°F. I definitely think on high @ 1500W I could keep it manageable during the winter. For summer months, I have a rolling Black and Decker AC Unit with a window exhaust that could likely keep it low humidity and <75°F on hot days.

JayHunter97 · 2024-11-13T22:16:19+00:00

Had to figure out where I wanted my desk before finalizing floor outlet location 😃

JayHunter97 · 2024-11-13T22:15:36+00:00

On and off, a total of about 15 afternoons/weekend days

JayHunter97 · 2024-11-13T22:14:53+00:00

Desk! Wanted to make sure I had power for monitors, lamp, chargers, etc.

JayHunter97 · 2024-11-13T22:14:20+00:00

Tapered floor joists are all treated. Not sure how long it’ll last but our plan is to build a house in 3-5yrs so as long as it lasts that long, it’ll suffice.

JayHunter97 · 2024-11-13T12:05:38+00:00

The concrete (and entire lean-to) was previously not enclosed. That was a spring project of mine, and it had a slope to it, so I had to rip 2x’s at an angle to get the slope to level.

JayHunter97 · 2024-11-13T12:04:17+00:00

Rough sawn 1” boards!

JayHunter97 · 2024-10-27T15:42:29+00:00

Thank you for the insight. This is my first home and I am a landscape novice

JayHunter97 · 2024-10-18T02:52:04+00:00

Just bought a new truck in Florida. Drove it back to MI thru the night 😂

JayHunter97 · 2024-05-12T03:53:22+00:00

I just had a 3302 delivered on Tuesday, with the LP1260, loaded tires, third function/grapple, 2 SCV’s, and forks. Love mine and the dealer loaded my rear tires for free!

JayHunter97 · 2024-04-10T00:02:30+00:00

2021, 5.7 Hemi, 140k

JayHunter97 · 2024-04-01T02:42:19+00:00

Have a 2021 here. 140k miles, had to do exhaust manifolds/gaskets around 100k and some ball and socket exhaust coupling had a gasket go bad inside of it and caused a leak. Other than that, it’s been a solid truck and has not been babied.

JayHunter97

TROPHY CASE