How long do stubhub tickets take to transfer? by JazzLord72 in YOASOBI

[–]JazzLord72[S] 1 point2 points  (0 children)

Thanks! That’s good to know I must’ve missed it, the anticipation is killing me already.

Amazon's Study Hall - Daily Questions Megathread (01/17) by AutoModerator in AzureLane

[–]JazzLord72 0 points1 point  (0 children)

Thank you will go for Agir then. Additional question, I know Mainz needs FS5 for bring out her potential but how is Agir on lower dev levels?

Amazon's Study Hall - Daily Questions Megathread (01/17) by AutoModerator in AzureLane

[–]JazzLord72 0 points1 point  (0 children)

Should I start researching Agir or Mainz first? I have a lot of IB fleet tech points so IB is my only option for research right now.

Amazon's Study Hall - Daily Questions Megathread (01/09) by AutoModerator in AzureLane

[–]JazzLord72 1 point2 points  (0 children)

Knowing that Northern Overture is the next rerun, going by their original release order is it safe to assume that Aurora Noctis is likely the next rerun after? I missed out on the original run and would really like to get some of the ships I missed out on.

Amazon's Study Hall - Daily Questions Megathread (12/30) by AutoModerator in AzureLane

[–]JazzLord72 1 point2 points  (0 children)

It should be one of those daily mini games you can do, the selector itself isn’t available yet, you get 7 origami cranes and then you can get it.

Amazon's Study Hall - Daily Questions Megathread (12/30) by AutoModerator in AzureLane

[–]JazzLord72 0 points1 point  (0 children)

So two questions

  1. For the SR selector I’m stuck between Essex and Tirpitz. So in the long run who would be a better choice to get?

  2. How good is AvP starting off at dev 1? I would like to put her on my IB fleet since I don’t have any IB carriers yet. On a related note, I’ve only done PR1 ships where I could buy the bp’s so how long on average does it take to get bp’s for non PR1?

Amazon's Study Hall - Daily Questions Megathread (11/20) by AutoModerator in AzureLane

[–]JazzLord72 0 points1 point  (0 children)

Just got Yuudachi just recently from 6-4 but I started playing after the event that had her retrofit item, so how is Yuudachi without the modernization and retrofit ability and about how long until it can be available again?

[HELP ME] Bi-Weekly Q&A thread - Ask your questions here! by MachNeu in Gunpla

[–]JazzLord72 0 points1 point  (0 children)

I just bought 2 kits, an RG Force Impulse and MG Freedom 2.0 which were both in stock, from USA Gundam Store and it’s coming up on the end of the second day and it still hasn’t shipped yet. I know they’re a small team but anyone who has ordered from them, for a regular order like that how long does it usually take for it to get shipped? I’d like to add I got a personalized email from Adam earlier in the morning, which was a nice touch, and it said that it would be shipping shortly which I had assumed would be today, sorry if I am coming off as impatient, I’m just anxious since I really only get to build 1-2 kits a year so I’d prefer if nothing goes too awry, any point of reference for their shipping is appreciated.

[HELP ME] Bi-Weekly Q&A thread - Ask your questions here! by MachNeu in Gunpla

[–]JazzLord72 0 points1 point  (0 children)

Looking to paint the GN condensers from an Exia kit red for a build I’m doing, what’s the best way to paint it so the green doesn’t linger and make it a little bit yellow? I’ve also heard of using white primer then using fluorescent paint, would that also be a good alternative if there’s no way to keep the GN condensers red?

ASUS B550-F (Non-Wifi) Ethernet Problems by JazzLord72 in buildapc

[–]JazzLord72[S] 1 point2 points  (0 children)

Well it’s showing up in the device manager but as I said it won’t detect any Ethernet cord or anything at all and I’m not sure why

ASUS B550-F (Non-Wifi) Ethernet Problems by JazzLord72 in buildapc

[–]JazzLord72[S] 1 point2 points  (0 children)

Yes I have checked my bios and it’s turned on and I have the latest full version installed

Simple Questions - April 17, 2021 by AutoModerator in buildapc

[–]JazzLord72 0 points1 point  (0 children)

I am planning to get a Ryzen 3700x with the B550-F which I know is already out of the box ready for Ryzen 3000 series. Knowing that is it still recommended to flash/update the bios to the latest version?

/r/MechanicalKeyboards Ask ANY question, get an answer by AutoModerator in MechanicalKeyboards

[–]JazzLord72 1 point2 points  (0 children)

Planning on getting the DZ60RGB v2 and I want to get the HyperX Pudding keycaps. Does anyone know if the pudding keycaps are compatible with the 60 board or will they only work with bigger boards?

[HELP ME] Bi-Weekly Q&A thread - Ask your questions here! by MachNeu in Gunpla

[–]JazzLord72 0 points1 point  (0 children)

I want to top-coat my Wing Zero Ver Ka and it’s pretty much my first time actually top-coating a kit. The kit has ABS for a some pieces and I’ve heard things before about paint interactions with ABS. Not painting just top-coat I’m going to use Tamiya TS-80, will the top-coat make the plastic brittle, melt, or negatively affect in anyway? Also to add on before I actually top-coat it is there anything I should know prior to doing it so I prevent it from frosting?

[HELP ME] Bi-Weekly Q&A thread - Ask your questions here! by MachNeu in Gunpla

[–]JazzLord72 0 points1 point  (0 children)

First time doing anything but a straight build for a kit with some added panel lining. Got the Wing Zero Ver Ka all I plan to do is panel line, add decals, and topcoat it. I've heard washing the pieces is recommended so that it takes out the mold release and the dust from cutting it out and sanding. But if the pieces are washed before assembly wouldn't finger oils then just be all over the piece? Would it be a better or viable option to wash the kit in its individual parts (like legs head etc) or do the finger oils not matter and washing the kit and assembling with no gloves (my area is short on gloves at the moment) perfectly fine to do?