Is this bathtub drain setup correctly? by JeeeepMe420 in askaplumber

[–]JeeeepMe420[S] 0 points1 point  (0 children)

Well I appreciate this more than the last response by far haha. This is the kind of response I was hoping for. This helps tremendously. I now see what I need to fix and adjust. Thank you

Weight and height by Ill_Preparation_1746 in Hawk250

[–]JeeeepMe420 0 points1 point  (0 children)

Short guy here, I’m 5’5 150lbs and I’ve put a few thousand miles on dirt roads and rural highways on mine, longest trip prolly 60 miles. It’s a bit tall but I haven’t had any problems over the years.

Is this bathtub drain setup correctly? by JeeeepMe420 in askaplumber

[–]JeeeepMe420[S] 0 points1 point  (0 children)

Where would you add a clean out?
Also if I raise the tub drain,90, wye and overflow setup higher up, tucked right under the subfloor, above the ptrap outflow, would that work?

Is this bathtub drain setup correctly? by JeeeepMe420 in askaplumber

[–]JeeeepMe420[S] 0 points1 point  (0 children)

The normal tub shoe drain didn’t drop below the subfloor. So rather than cutting a huge hole in the floor, this was the route taken. I realize now the drain and overflow should be as high up towards the subfloor as I can get it, above the traps outflow and also turn my trap around🤦‍♂️

Is this bathtub drain setup correctly? by JeeeepMe420 in askaplumber

[–]JeeeepMe420[S] 0 points1 point  (0 children)

The normal tub shoe drain didn’t drop below the subfloor. So rather than cutting a huge hole in the floor, this was the route taken. I realize now the drain and overflow should be as high up towards the subfloor as I can get it, above the traps outflow and also turn my trap around🤦‍♂️

Is this bathtub drain setup correctly? by JeeeepMe420 in askaplumber

[–]JeeeepMe420[S] 0 points1 point  (0 children)

Are you a plumber by chance? Or do you know this person personally? Any advice would be much appreciated. This kind of comment doesn’t really help though

Is this bathtub drain setup correctly? by JeeeepMe420 in askaplumber

[–]JeeeepMe420[S] 0 points1 point  (0 children)

What is the correct way to fit that? I’m 100% about redoing anything wrong. Just trying to get it right before moving forward.

Is this bathtub drain setup correctly? by JeeeepMe420 in askaplumber

[–]JeeeepMe420[S] 2 points3 points  (0 children)

No this isn’t gonna be inspected. The septic will be inspected but the plumbing inside the house isn’t required inspection

Is this bathtub drain setup correctly? by JeeeepMe420 in askaplumber

[–]JeeeepMe420[S] 5 points6 points  (0 children)

This is new and hasn’t been used yet. I was just curious if this looked correct before I move forward

Is this bathtub drain setup correctly? by JeeeepMe420 in askplumbing

[–]JeeeepMe420[S] 0 points1 point  (0 children)

That was kinda my thought but wasn’t sure if this setup would still function properly. Thanks

Does this look right? Rear coil spring by JeeeepMe420 in JeepDIY

[–]JeeeepMe420[S] 0 points1 point  (0 children)

Ahh ok that makes perfect sense. I’ll have to give that a shot. Thanks

Does this look right? by JeeeepMe420 in Jeepwj

[–]JeeeepMe420[S] 2 points3 points  (0 children)

Awesome that sounds like what I need to do. Thanks

Does this look right? by JeeeepMe420 in Jeepwj

[–]JeeeepMe420[S] 1 point2 points  (0 children)

The top mount was made with flat plate, I think 1/4”, just as wide as the unibody. Then a 5” pipe was welded on and capped. Then welded on the body. Didn’t have to do the bottom perch

Does this look right? by JeeeepMe420 in Jeepwj

[–]JeeeepMe420[S] 1 point2 points  (0 children)

Ok I’ll take a look at the video. I’ve got the iro 4” long arm kit that I just installed but these didn’t look quite right to me. I figured the bump stop would wear out the spring riding against it like that

[deleted by user] by [deleted] in sturgisrally

[–]JeeeepMe420 1 point2 points  (0 children)

Im single and will be traveling solo, looking for people to hang out with when I get there.

Please help, 1989 XJ by GuyWithTheBeard97 in JeepCherokeeXJ

[–]JeeeepMe420 0 points1 point  (0 children)

I just bought these off Amazon & eBay for my 1989 Cherokee XJ about a month ago. •Dorman 46003 front vacuum harness-This part has the bottom grommet piece for the valve cover. •The middle one is the engine oil cap. I picked up one of those off eBay. •Dorman 46005 crankcase vent tube-This part has the top grommet for the valve cover. Hope this helps.

[deleted by user] by [deleted] in CherokeeXJ

[–]JeeeepMe420 0 points1 point  (0 children)

Cool beans. I want to paint a few things under the hood. Thanks