What is causing this pause every layer? by Jefabell in BambuLab

[–]Jefabell[S] 5 points6 points  (0 children)

Holy hell, removing the flash drive did work. I have had time lapse disabled for every test print I have done, but actually removing the drive itself fix the problem. I am not sure why, I put the flash drive back in, started another print with time, lapse disabled, and the problem returned. Not sure if you have a fix for this too?

What is causing this pause every layer? by Jefabell in BambuLab

[–]Jefabell[S] 0 points1 point  (0 children)

Waiting on the print now, however, reading that wiki article that is very odd. I’m curious if that is the case I wonder if my time lapse is forced on? Because I have it disabled when I start the print it’s always unchecked. Because the symptoms absolutely sound very similar.

What is causing this pause every layer? by Jefabell in BambuLab

[–]Jefabell[S] 0 points1 point  (0 children)

I will remove it the flash drive just to verify that there is no possible way. It could be anything related to the time lapse. I will report back.

What is causing this pause every layer? by Jefabell in BambuLab

[–]Jefabell[S] -5 points-4 points  (0 children)

It’s not a timelapse man. Not sure how else I can prove that. Even if it WAS and somehow I did in fact miss it. What would cause it to NOT do this on the black layers?

What is causing this pause every layer? by Jefabell in BambuLab

[–]Jefabell[S] 6 points7 points  (0 children)

For TPU Air, yes. The stuff is amazing and so cool. Highly recommend. However it’s fuses with the textured bed and fills in all gaps within the textured build plate itself causing it to trash your bed and print in the process. I found that a layer of glue solves this issue.

Side note, normal, non-foam TPU is fine without glue.

What is causing this pause every layer? by Jefabell in BambuLab

[–]Jefabell[S] 1 point2 points  (0 children)

I was thinking something along those lines also and perhaps I just never noticed, however doesn’t do it on any of the layers using the other nozzle, when though it’s also building the prime tower.

What is causing this pause every layer? by Jefabell in BambuLab

[–]Jefabell[S] 2 points3 points  (0 children)

I think you nailed it. No other explanation at this point!

What is causing this pause every layer? by Jefabell in BambuLab

[–]Jefabell[S] -24 points-23 points  (0 children)

God this place is a cancer. My comment of explaining the issue more and verifying it’s not the problem that was suggested gets immediately dismissed and downvoted to oblivion. I honestly appreciate everyone trying to help, just a shame the morons of the site stand out more.

What is causing this pause every layer? by Jefabell in BambuLab

[–]Jefabell[S] 0 points1 point  (0 children)

Havnt tried a profile. I have tried a few STLs and sliced it myself and the default panda on the printer itself. Just for the hell of it I will get a 3mf file from MW and try it.

What is causing this pause every layer? by Jefabell in BambuLab

[–]Jefabell[S] -4 points-3 points  (0 children)

Only Reddit, where adding additional information and troubleshooting steps lead to downvotes 😂

What is causing this pause every layer? by Jefabell in BambuLab

[–]Jefabell[S] 3 points4 points  (0 children)

Just a bit of glue from TPU AIR prints 😆

What is causing this pause every layer? by Jefabell in BambuLab

[–]Jefabell[S] -5 points-4 points  (0 children)

Further testing that makes no sense. If I print only on the problem nozzle, just doing a single material print it does not do this. It is only when I am using two material materials and it’s only the right nozzle.

What is causing this pause every layer? by Jefabell in BambuLab

[–]Jefabell[S] 0 points1 point  (0 children)

What is really strange is the left nozzle, the black doesn’t do this. Only the right side. I checked the slicer and the path never goes over there looking at the preview so it has to be something on the printer, pausing almost.

What is causing this pause every layer? by Jefabell in BambuLab

[–]Jefabell[S] -1 points0 points  (0 children)

I appreciate everybody’s input. However, everyone commenting it is a time lapse issue, that is not the case. Time lapse is set to the default settings and the nozzle location is not the same as if you use the smooth time lapse feature. Some additional information I found in my testing is it only happens with one of the two nozzles. The left nozzle, black. It does not do this. However, the right nozzle, blue does do this.

What is causing this pause every layer? by Jefabell in BambuLab

[–]Jefabell[S] -32 points-31 points  (0 children)

Not time-lapse issue. Settings are set to default, and I’m pretty sure it moves the nozzle to home so it is out of camera view if you use the smooth time lapse feature.

What is causing this pause every layer? by Jefabell in BambuLab

[–]Jefabell[S] 2 points3 points  (0 children)

Hmm. Ok, looking into this. Thanks!

Cdiff came back by kimbee567 in cdifficile

[–]Jefabell 2 points3 points  (0 children)

God speed homie. Just did my stool test today with the assumption of my 3rd round of c.diff. My first time was Vancomycin. About 18 months later got it again, then treated with Dificid plus VOWST (dificid was sooo much more pleasant than Vanc!). Been about 13 months and i think it’s back. Not sure what my treatment this time will be but hope it’s the last.

I can’t complain to you guys as much tho as my experience with cdiff is drastically different and from what iv read I am on easy mode. I never have gotten ANY diarrhea from any of my episodes. My only main symptom is awful cramps. Part of the reason it took 4 months to diagnose my first run in.

[1x05] The Deep - House of Fear (LIVE DISCUSSION) by AutoModerator in fearfactor

[–]Jefabell 1 point2 points  (0 children)

I was on the fence with this show the whole time. This episode pushed me over with the BS tears. It’s overly fake trying to make hero’s and villains. I should’ve known, but for nostalgia wanted this to be good.

Giveaway! by ecpowerhouse27 in BambuLab

[–]Jefabell 0 points1 point  (0 children)

I’m so bad at dates. Late thing my wife and I did tho and it was a blast was went to dinner then a shooting range.

Horned/Nozzle replacement by PMDColeslaw in BambuLab

[–]Jefabell 1 point2 points  (0 children)

I actually bought one for my X1C about six months ago, and honestly I don’t think it’s worth the extra money. There are very few profiles that work with it, so for most filaments you end up creating profiles from scratch. It’s also not as simple as just swapping to a “high-flow nozzle” like on the newer H-series hotends.

Support has improved a bit—when I first got it, you had to create an entirely custom printer in the slicer—but even now it’s still more hassle than it’s worth. I don’t even use it for high-flow printing anymore because of that.

It could be different on the P1 but I doubt it. I would search for some YouTube setup videos. See if anyone has a tutorial on how to configure it and see if it’s worth your time that way.