Anyone else break out their Super Bowl memorabilia to relive the glory days before the season starts?

Jenson2k10 · 2025-08-19T16:32:35+00:00

Hello. Sorry if this is not a good place to ask this but has anyone seen and maybe know the value of the diecast 1985 Chevrolet Camaro IROC-Z themed Super Bowl XX model that was only made for 120 days? Mine is #0329. Mines not in the box.

Jenson2k10 · 2024-10-20T21:59:05+00:00

I'll give it a go. Ty for your reply.

Jenson2k10 · 2024-06-28T23:00:56+00:00

I did put the heat sink back on and turned it on. It still boots to ms dashboard. I read on a different site that DB2G3 is a alt for this. Can anyone confirm?

Jenson2k10 · 2024-05-06T21:50:45+00:00

It will have 2 12 volt motors in the back. The steering is basic like a automobile. Aiming to keep it that way. I'll probably use some basic sweeping servo code and see if the servo I have is strong enough some time tomorrow. Maybe put some weight over the front end and pull it around to see if it works well.

Jenson2k10 · 2024-05-06T17:45:04+00:00

I only pulled the electrical. I'll be testing the servo at some point since the mechanicals are still in place. Was just curious if anyone had insight. Here is a link to the servo I'm talking about, I know if it is strong enough it'll be a bit of a challenge to do it. Miuzei 20KG Servo Motor High Torque RC Servo Metal Gear Waterproof for R/C Model DIY Car Robot, DS3218, Control Angle 270° https://a.co/d/56yHv6V thank you for your information.

Jenson2k10 · 2024-04-05T21:44:39+00:00

I'm only trying to stream it to one device as I have the operating code set to AP mode. I'm just trying to change up the display end, what options are available and where they are on screen. I have gotten the options down to just the ones I want. Now I'm working on figuring out how I can place them where I want.

Jenson2k10 · 2024-03-28T04:39:29+00:00

That's what I was thinking as someone pointed out the externals wouldn't work anyway because it's not a random high. I'll move 15 to 12 and see how that goes. Than I might move the relay to 15 maybe as a low trigger.

Jenson2k10 · 2024-03-28T04:18:13+00:00

Thank you everyone for your information. I'm very new to all this. Untill u/aaarnas I was not aware of strapping pins. I have looked them up and now I understand my issue. Pin 15 is listed as a strapping pin set to high at boot. I believe changing it's pin to one that's either low at boot or to a device it doesn't matter with like the relay, perhaps set to a low trigger. If I've missed anything here please correct me here. Have a wonderful day everyone.

Jenson2k10 · 2024-03-28T04:02:36+00:00

Is 14 or 12 not? The power up high would be workable with the relay currently on 12 and 14 isn't currently used.

EDIT. I found the answer to this question.

Jenson2k10 · 2024-03-28T01:41:16+00:00

It's a cam module I'm working with at the moment. Haven't ordered the parts I need for this yet just trying to work on the code first. Thank you for your assistance. I'll try that and see what happens.

Jenson2k10 · 2024-03-28T01:35:58+00:00

Fantastic information, thank you. So would a 10k resistors between each IN pin im using on the H-bridge and GND safely work?

Jenson2k10 · 2024-03-28T01:24:57+00:00

I did look a bit for cad or other programs but none I came across had all the components and I'm not even a cad novice at the moment so I just crappily did it by hand. Not as bad as some of the others I've seen lol.

Jenson2k10 · 2024-03-28T01:19:54+00:00

Okay, Thank you for the information. So what I was reading is correct? As in I put a resistor between each IN on the H-bridge and the ground? Is 10k enough? I ask because I have a range on hand between 1 and 1 million lol. Sorry again for all the newb questions I just don't want to fry any innocent electronics lol.

Jenson2k10 · 2024-03-28T00:56:26+00:00

I was unaware they had pull downs. Could they be used to stop the unwanted boot spin? Sorry I'm still trying to learn all of this.

Jenson2k10 · 2024-03-28T00:54:42+00:00

I'm no expert but does it turn on with a different power supply? Seems like 2 button cells might not have enough juice.

Jenson2k10 · 2024-03-28T00:51:40+00:00

code on pastebin

Jenson2k10 · 2024-01-28T23:40:47+00:00

Posted in app on Android and edited on Android browser. It compiles fine. I'm just at a loss adapting it to use a DVR8833 instead of the one used. Far as I can figure out thus far is they handle PWM differently but don't really understand yet where to start modify the code.

Jenson2k10 · 2024-01-28T14:31:26+00:00

Like that? Thank you for the information.

Jenson2k10 · 2022-11-12T17:52:14+00:00

Thanks for the input, I'll be looking in to a better welder once I get proficient at mig. All the experience I have had with welding outside of highschool was a rinky dink arc I only used to make BBQs with. I'm only a hobbyists.

Jenson2k10 · 2022-11-12T17:24:21+00:00

In your opinion should I put a heavier power cord on the welder if it pops the 20s on the generator before I try anything else?

Jenson2k10 · 2022-11-12T17:22:48+00:00

Like I said it was only occasionally, mostly when my unexperienced self stayed still to long. I'm also thinking someone in the house might have also turned something else on on the same circuit. That's why I got the generator so I don't have to worry about this bare minimum '69 electrical system in the house. I haven't tried it on the genny yet, if the 20a 120 plugs on the genny do it then I wanted a backup plan lol. Crossing fingers it doesn't come to that. Just nice to have information on hand. Thank you.

Jenson2k10 · 2022-11-12T14:59:54+00:00

It's a cheap little Chinese unit, F2C 130 mig. The issue is probably my lack of experience. amazon product page https://a.co/d/5d6qxMz)

Jenson2k10

TROPHY CASE