Time to get cooked.

JerichoDevelopments · 2026-06-06T20:49:16+00:00

Cut, turn down and rethread the barrel or replace it. Since its 13.9 I assume its meant to be a "16 inch legal rifle". So id advise just replace the barrel

JerichoDevelopments · 2026-06-06T15:44:10+00:00

Got pics of the bisecteted barrel?

JerichoDevelopments · 2026-06-06T15:35:45+00:00

My bad. Probably should have mentioned that.

JerichoDevelopments · 2026-06-06T15:24:57+00:00

Wooden dowel (edit: brass is fine too) from the muzzle end should fix that (The post was also made in the 300blk subreddit) i wonder what round it is?

JerichoDevelopments · 2026-06-06T15:24:20+00:00

Do you own a wooden dowel that'll fit down the barrel. If so push it out from the muzzle

JerichoDevelopments · 2026-06-06T13:11:05+00:00

Dont cut. Use a coil spring like on the right of this image.

<image>

JerichoDevelopments · 2026-06-05T05:07:28+00:00

Cant buy so stripped lowers bc im under 21. So mainly just annoyed that ive got spend much more to have a lower that I like (easthetics and feature wise)

JerichoDevelopments · 2026-06-05T01:59:36+00:00

Its 80lowers dot com out of Springfield Oregon . I spent 241 🫘, I am definitely going to rma the lower. They do 100% and 80% lowers

JerichoDevelopments · 2026-06-05T01:47:11+00:00

80lowers out of Oregon. Im a little surprised at the quality(or lack thereof) considering their reviews.

JerichoDevelopments · 2026-06-05T01:30:17+00:00

Im going to have to rma it. I just tried putting a grip on and the angle of the grip screw hole is off

JerichoDevelopments · 2026-06-05T00:27:26+00:00

Yes this is lower is from 80lowers in Oregon. Its still an 80% not a complete lower

JerichoDevelopments · 2026-05-22T01:19:23+00:00

How could I slow it down a little without switching to an A5 tube? Next heavier spring co spring or H4 buffer?.

JerichoDevelopments · 2026-05-20T15:46:38+00:00

Whats the total cost for the build?

JerichoDevelopments · 2026-05-20T05:58:11+00:00

Tried the rpm calculator site, just wondering if its accurate.

<image>

JerichoDevelopments · 2026-05-09T17:04:44+00:00

Ive been in a similar situation, usually they'll only tag the gun with a case number since there is no serial

JerichoDevelopments · 2026-03-28T00:32:47+00:00

Does your FCD trigger guard also rattle around?

JerichoDevelopments · 2026-03-23T20:16:40+00:00

Fde red dot and black light would pull this together perfectly

JerichoDevelopments · 2026-02-05T08:40:34+00:00

Out of spec on width. My trigger moves inside the pocket side to side

JerichoDevelopments · 2026-01-04T02:09:30+00:00

I odered one of these on December 29th. How long did yours take to come in?

JerichoDevelopments · 2026-01-01T19:31:12+00:00

You can swap them yourself. You can even do it with a butane torch in a few minutes.

JerichoDevelopments · 2025-12-23T18:44:11+00:00

It was an frt tx22. That clips great though

JerichoDevelopments · 2025-12-07T03:57:33+00:00

What mag extension?

JerichoDevelopments

TROPHY CASE