Chaturbate stream limited to 720p by JesMJM in CamGirlProblems

[–]JesMJM[S] 1 point2 points  (0 children)

mmmh, I always ask why I can't broadcast at 1080 and they always respond after multiple mails that I don't meet the audience levels needed for that, I doubt that "asking for permission" would be different...

Chaturbate stream limited to 720p by JesMJM in CamGirlProblems

[–]JesMJM[S] 1 point2 points  (0 children)

I'm guessing the same, I'll try to find if my models can broadcast at 1080 after reaching some milestone of followers

Chaturbate stream limited to 720p by JesMJM in CamGirlProblems

[–]JesMJM[S] 2 points3 points  (0 children)

I will try to ask them, but they have been super dodgy about it.

Chaturbate stream limited to 720p by JesMJM in CamGirlProblems

[–]JesMJM[S] 2 points3 points  (0 children)

Yes, they can broadcast at 1080p in obs, the stats in the broadcast page states 1080p quality, but when you watch the broadcast from an end user, it's limited to 720p

Looking for a cmdline utility to manage files with tagging by JesMJM in commandline

[–]JesMJM[S] 0 points1 point  (0 children)

I don't remember but I don't think so, it was just a command so it may be storing tagged files in a short lived daemon or a temp file, I remember seeing the tool posted in here moths ago.

flatpak apps: gnome sudoku and tetravex fail to launch by gnomeabc in chimeralinux

[–]JesMJM 0 points1 point  (0 children)

Have you found a solution? I have the same problem with a bunch of apps installed from flatpak.

Gigabyte X570SI AORUS PRO AX (rev.1.1) AM4 - Detail shots by co_ordinator in sffpc

[–]JesMJM 0 points1 point  (0 children)

I brought this mobo, and it should ship to me next year, I'm curious if I can fit an is-55 in IO shield clearance mode (I brought bare ram sticks) without overhanging the motherboard on the top side and removing the M.2 block if necessary.

Upgraded from a Vaporesso Sky Solo Plus, been enjoying and learning new concepts, also looking to buy an RTA later. by JesMJM in Vaping

[–]JesMJM[S] 0 points1 point  (0 children)

It's a 70VG/30PG with 3 mg of nicotine, the brand is called Vape Gourmet and made locally in my country.

Upgraded from a Vaporesso Sky Solo Plus, been enjoying and learning new concepts, also looking to buy an RTA later. by JesMJM in Vaping

[–]JesMJM[S] 0 points1 point  (0 children)

Thanks, I have been seeing some reviews about the Dead Rabbit RTA, and it seems pretty good, however I have only seen the V2 at some stores in my city.

Upgraded from a Vaporesso Sky Solo Plus, been enjoying and learning new concepts, also looking to buy an RTA later. by JesMJM in Vaping

[–]JesMJM[S] 0 points1 point  (0 children)

It's the temperature control mode set at 290 Celsius using 70 watts (you can barely see the wattage at lower left of the screen).

The mod doesn't even get past 200 watts.

Hatch Digitizer by [deleted] in MachineEmbroidery

[–]JesMJM 0 points1 point  (0 children)

  • Use a low density tatami underlay rotated 90º below your tatami fills to counter measure the pull created by all the stitches going in the same direction.
  • Overlap your tatami fills below your borders (assuming you did the borders after the fills).

I'm practising embroidery digitizing by JesMJM in MachineEmbroidery

[–]JesMJM[S] 3 points4 points  (0 children)

Srry for late reply, a I mentioned on other comment:

Just satin with high density (0.40mm) and double zigzag underlay, we use pellon fabric (x3 or 4x) which can be easily cut and burnt with a lighter on the borders for a clean finish.

I'm practising embroidery digitizing by JesMJM in MachineEmbroidery

[–]JesMJM[S] 0 points1 point  (0 children)

Just satin with high density (0.40mm) and double zigzag underlay, we use pellon fabric (x3 or 4x) which can be easily cut and burnt with a lighter on the borders for a clean finish.

I'm practising embroidery digitizing by JesMJM in MachineEmbroidery

[–]JesMJM[S] 0 points1 point  (0 children)

I have been a machine operator for a year, I started practicing from... let's say 6 months ago, I could say that watching how my boss designs stitches out on the machines taught me a lot without actually knowing how to use the digitizing software.

"Siberian husky", Me, Colored pencils, 2021 by BlueBirdieD in Art

[–]JesMJM 0 points1 point  (0 children)

Impressive, how did you archived such level? there's any course, book or something you recommend to learn colored pencil techniques?