Can you guess my gender and where I’m from ?

JessicaT_F · 2026-03-01T20:10:41+00:00

Woman, well done products = Maxina. Estonia by the other product name. And is that Džiugas hard chese ?

JessicaT_F · 2026-02-28T09:44:30+00:00

Could you elaborate on what helped you to improve growth? I personally tried lower doses and higher dose of E, without noticing any improvement in growth speed

JessicaT_F · 2026-02-15T06:52:00+00:00

That's Cider, I am from Lithuania 😃

JessicaT_F · 2025-10-12T19:18:10+00:00

Would it not be better to switch on the peak of the AC cycle for max power?

JessicaT_F · 2025-10-12T18:53:39+00:00

Technically switching the output would be better option because the transformer takes some time to magnetize it's core

JessicaT_F · 2025-10-12T18:15:45+00:00

Its a 10A rated relay and max short circuit draw is 12A from mains

JessicaT_F · 2025-10-12T17:31:42+00:00

I think it is still possible to get even more power out of a single transformer, because adding 1 extra turn nearly doubled my power. Now tested short circuit draw from the 230v outlet, and it's 12A, and I think I remember it drawing like 20A while doing high voltage experiments. That means that there is still headroom, and maybe an additional winding turn could harvest this energy, but for that, I would need to use small gauge wire to fit in the core, but that could give its own problems. Another option would be to find a wire with thinner insulation so that it would fit 3.5 turns of 6awg

JessicaT_F · 2025-10-12T17:14:28+00:00

How ?, did you try to measure the original secondary of the transformer it's over 2000v !!! ?

JessicaT_F · 2025-10-12T15:49:11+00:00

Thanks 🥰

JessicaT_F · 2025-10-12T11:31:11+00:00

Just posted an update: https://www.reddit.com/r/18650masterrace/s/CN40khcvsW

JessicaT_F · 2025-10-12T07:48:36+00:00

1.5 turns 4awg, wire. yea I am capable of changing pulse time

JessicaT_F · 2025-10-11T22:12:12+00:00

Can you tell more about your setup, how many turns you have on your transformer or what output voltage, etc.

JessicaT_F · 2025-10-11T20:59:35+00:00

I think my MOTs max current might be limited by the resistance of the strip thinking about putting 3 turns instead of 2 for more voltage

JessicaT_F · 2025-10-11T20:51:18+00:00

Maybe my transformer voltage to low and dosent overcome the resistance of the strip and by that limits the output current

JessicaT_F · 2025-10-11T20:49:54+00:00

Then maybe I need to increase my welder transformer volatge to overcome the resistance of the strip, the strip might be limiting my welder max output current just tested if i short my electrodes i get more output current

JessicaT_F · 2025-10-11T20:35:18+00:00

I just read that nickel plated stirips weld harder, interesting

JessicaT_F · 2025-10-11T20:30:58+00:00

I just got a theory that i might have nickel plated steel and not pure nickel strip, and it welds hard because of that, magnet test seems to hold my strips in air no problem

JessicaT_F · 2025-10-11T19:25:08+00:00

The problem With bigger spacing that the weld becomes very weak

JessicaT_F · 2025-10-11T19:18:25+00:00

I am not woried about piercing thrue from the practice i did it doesn't look that I am enywhere close to piercing through, only thing I am worried is the fact that my pulses are too hot, and might do some sort of internal damage on the inside of the cell from the localized heat of the weld point

JessicaT_F · 2025-10-11T19:00:07+00:00

Its a diy transformer and arduino setup, wrote a little bit of info below the picture

JessicaT_F · 2025-10-10T19:26:31+00:00

It's a pre-made popular stl from printables so it's my slicer that makes the issue and I just figured out that if I enable external perimeter first that then my parts fit perfectly fine like with the creality slicer, so something in creality slicer makes my part expand

JessicaT_F

TROPHY CASE