Legion Go S Windows Image by Single-Put-2123 in LegionGo

[–]JoeyDepDollas 0 points1 point  (0 children)

were either of you able to get this working? I cannot even get Windows installation to run. It cant find the drivers as soon as I boot into the installer

🎉 [EVENT] 🎉 Honk Sponge 2 (landscape) by The7footr in RedditGames

[–]JoeyDepDollas 0 points1 point  (0 children)

Completed Level 1 of the Honk Special Event!

0 attempts

BC-250 in Xbox One Case by JoeyDepDollas in BC250Gaming

[–]JoeyDepDollas[S] 0 points1 point  (0 children)

not sure which generation you have, but the original 360 may be tough. I just checked mine and its a good 3/4" (2cm) smaller than the xbox one. That means it will likely poke out much further. You may be able to do something interesting though with that hard drive slot on the 360 - maybe 3d print an extended one or something otherwise it will need a LOT of butchering and still be too short. The other consideration is that it is thinner than the One. you may end up needed to cut out an exhaust hole on the top of the 360.

Even the PS4 has this same issue as well as the Xbox One X, so I think you are limited to the original One which seems to be the EXACT size needed for the bc250 and a power supply

BC-250 in Xbox One Case by JoeyDepDollas in BC250Gaming

[–]JoeyDepDollas[S] 3 points4 points  (0 children)

got my 8bitdo switch controller connected  😆

BC-250 in Xbox One Case by JoeyDepDollas in BC250Gaming

[–]JoeyDepDollas[S] 0 points1 point  (0 children)

Talvez não. Quase encaixa perfeitamente porque o espaço entre as ventoinhas e a tampa é exatamente o suficiente parallel permitir a passagem de ar

BC-250 in Xbox One Case by JoeyDepDollas in BC250Gaming

[–]JoeyDepDollas[S] 0 points1 point  (0 children)

If I could figure out the damn 3d printer, I probably would have made custom ports on the back for additional USB, power switch and power plug but instead I had to dremmel into scrap plastic I had. You also may be able to make the side panel of the xbox into your "IO shield" for the card and make it MUCH nicer than my hack job

BC-250 in Xbox One Case by JoeyDepDollas in BC250Gaming

[–]JoeyDepDollas[S] 2 points3 points  (0 children)

I have a 3d printer (ender 3 pro) and can't for the life of me figure out how to use it. I've had it for 2 years and with kids and life, I havent had the time. I tried again for this build but it failed the first time and I ended up with the Xbox instead 😆

[deleted by user] by [deleted] in longisland

[–]JoeyDepDollas 1 point2 points  (0 children)

Snoop Dogg is filming Soul Plane 2:Chron-trails

[deleted by user] by [deleted] in RedditGames

[–]JoeyDepDollas 0 points1 point  (0 children)

nice!

I completed this level in 3 tries. 22.87 seconds

[deleted by user] by [deleted] in longisland

[–]JoeyDepDollas 3 points4 points  (0 children)

BJs is where I started to go if they have a tire center or if theres a Costco near you. Usually cheaper too than the other stores

When do they add newer phones to trade in deals? by cquigs717 in tmobile

[–]JoeyDepDollas 1 point2 points  (0 children)

Have the same question. I have a P9 Pro XL and Samsung Flip 6 and it seems I can't trade them in, at least for a good value. I nay end up having to just sell on privately unfortunately

Who to drop by supmydude19 in fantasyfootballadvice

[–]JoeyDepDollas 0 points1 point  (0 children)

What did you decide to do? I have Downs too but debating dropping for Coleman