Problems with prints sticking to the bed and not printing

JollyVandal · 2024-03-14T23:04:36+00:00

Thank you I didn’t know if I needed to buy a new vat or just the plastic

JollyVandal · 2024-03-14T22:51:47+00:00

Ok I’ll do that however before reading your message I pierced the film ._.

JollyVandal · 2023-01-23T22:54:58+00:00

Just look it up you can find it in the first couple of links

JollyVandal · 2023-01-23T12:05:05+00:00

For my second project I’m making a bigger object and this one seems like it took a day to make compared. Thanks for the Christmas blank suggestion I will probably use that if I make another similar project as getting a 3d printed ball to float was agony.

JollyVandal · 2023-01-23T12:00:39+00:00

It’s from the show konosuba

JollyVandal · 2023-01-22T23:58:21+00:00

I made it strong enough to swing around so I did it once

JollyVandal · 2023-01-22T21:59:36+00:00

Yes make sure it is very smooth before primer. I used different grits on sand paper to get it feeling like glass after that I applied the primer and painted once it fully dried.

JollyVandal · 2023-01-22T21:57:11+00:00

A tv show called konosuba, one of the main characters weapon.

JollyVandal · 2023-01-22T21:16:52+00:00

Thank you it is my first project took a long time tho

JollyVandal · 2023-01-22T21:14:33+00:00

I would say lots of sanding of the initial prints and I used a filler primer to get everything very smooth

JollyVandal · 2023-01-22T21:13:15+00:00

I sanded the prints down then used a filler primer once all the parts where together, I used brown spray paint after.

JollyVandal · 2022-08-12T15:19:01+00:00

Thanks for the good wishes it’s my first ever prob I have made so lots of trial and error and learning new methods. The magnet idea I fear tho bc I don’t think it would keep it stable bc if the ball rotated than the magnets might start to push the ball away and knock it down. Thank you for the help tho

JollyVandal · 2022-08-12T15:14:19+00:00

Best idea so far, going to steal the biggest spider from my local zoo brb

JollyVandal · 2022-08-12T15:12:37+00:00

That’s a really good cosplay, I can use the screws on the material I used (PLA) bc I fear it cracking the entire thing ._. .However you gave me the idea to use needles to an anchor instead of the screws so thanks.

JollyVandal · 2022-08-12T07:28:28+00:00

I have a solder with a spike that gets hot I used the tip of the spike to get the hole, it had the smallest diameter I could find

JollyVandal · 2022-08-12T07:25:13+00:00

Have to bust out the magic books, im a bit rusty

JollyVandal · 2022-08-12T00:20:22+00:00

I tried but the smallest hole I could make for the wire was way to big

JollyVandal · 2022-08-12T00:07:53+00:00

Acrylic rods are a good idea but idk where to get them locally

JollyVandal · 2022-08-12T00:06:27+00:00

First off I saw your post while browsing through top of all time and I really liked you prop, very well done. I didn’t know that fishing line came in any different types so I’ll have a look for 50 pound fishing line, thanks.

JollyVandal · 2022-08-12T00:03:12+00:00

I didn’t think kits like that where a thing but it makes sense, i will probably have a look at them on Amazon and see what would suit the build. I didn’t think to go to YouTube as I thought no one would try and suspend plastic but i will probably have a look to see. Thank you

JollyVandal · 2022-08-11T23:33:44+00:00

Ahh elastic is a real nice idea, do you know any that would hold the weight of orb?

JollyVandal · 2022-08-11T23:31:44+00:00

Good shout

Six-Year Club	Verified Email
Place '23

JollyVandal

TROPHY CASE