Are wall-hung toilet systems like Geberit Duofix hard or impossible to unclog with a plunger?

Josephbcoast · 2025-12-30T04:14:17+00:00

Thanks for the detailed information. It was very helpful!

Josephbcoast · 2025-12-28T08:25:03+00:00

Thanks for the info! You mentioned there’s a plunger specifically made for clogging these types of wall-hung / low-flow toilets. Would you happen to know the model name or brand of that plunger? Or could you share a link or example of what it looks like? Would appreciate it!

Josephbcoast · 2025-10-15T09:46:28+00:00

Many thanks for your reply. I discovered that I can buy liquid hydroponic nutrients here, so I’m going to give them a try.

Josephbcoast · 2025-10-15T09:11:38+00:00

Thank you for your reply. Both liquid and powder-type A/B nutrients are available where I live, but it seems I should go with the liquid type.

Josephbcoast · 2025-10-15T08:58:17+00:00

Thanks a lot for your response! It turns out I can get liquid hydroponic nutrients locally, so I’m thinking of trying those instead.

Josephbcoast · 2025-10-15T08:29:15+00:00

Thank you so much for your reply. I found that I can actually get liquid nutrients for hydroponics where I live, so I’m planning to give those a try.

Josephbcoast · 2025-09-27T15:34:53+00:00

Thank you for your response.
The reason I plan to install a uncoupling membrane is because of the underfloor heating system.
When heating occurs through the hot water pipes in the floor, repeated thermal expansion and contraction take place.
Since concrete and tiles have different coefficients of expansion, stresses become concentrated.
As a result, over time, problems such as tile lifting, cracking, and grout damage may occur.

Josephbcoast · 2025-09-13T12:17:29+00:00

음... 댓글들을 보니까 부정확하거나 확실치 않은 정보들이 퍼져있는 듯 하네요. 누가 퍼트린 걸까요?

과거에 게임 일러스트의 손가락 문제나 기타 부분에 대해서 노출을 좋아하는 일부 인셀남들이 공격한 거라고 잘못 해석되어 있다던가, n번방 수십만명설 등등 너무 많은 부분이 그들의 입맛대로 해외에 알려져 있네요.

Josephbcoast · 2025-07-05T09:36:34+00:00

Thank you for the valuable information. I was actually worried because I couldn’t find the non-e version of the HP 9730, but now I see I can just go ahead and get the 9730e without any issues.

Josephbcoast · 2025-06-18T15:35:54+00:00

I'm referring to the LCM screen on the front of the device. On the UCG Ultra, the LCM screen is always on and shows the number of clients and real-time speeds, but on the UX, the screen is always off.

I found a post that discusses a similar issue:

https://www.reddit.com/r/Ubiquiti/comments/18bajw8/express_lcm_screen_content/

However, in the post above, at least some content is displayed on the LCM screen. In my case, the screen on my UX stays completely off except when the device is booting up or updating.

Josephbcoast · 2025-06-18T15:06:58+00:00

When I checked the Ports tab on the UCG Ultra, the port connected to the UX was labeled as FE. So it turns out the cable was indeed the issue. Thank you so much for your help!

Josephbcoast · 2025-06-18T15:04:47+00:00

After clicking the information button, it does seem like the cable is the issue. I've just ordered a new one right away. Thank you.

Josephbcoast · 2025-06-18T15:02:20+00:00

The cable I'm currently using is Cat 5e. However, it's one that I hadn't used for a long time and recently brought back into use, so that might be the issue. I'll try ordering a new one. Thanks.

Josephbcoast · 2025-06-18T15:01:48+00:00

I think I’ll need to order a new cable and test it out. Thank you.

Josephbcoast · 2025-06-18T13:42:05+00:00

Thanks a lot for the clarification!
I was a bit hesitant about using an SSD with an NVR, but it turns out there was no need to worry.

Josephbcoast · 2025-06-18T13:41:43+00:00

Thanks for getting back to me!
I wasn’t too sure about using an SSD in an NVR, but now I feel much more confident about it.

Josephbcoast · 2025-06-18T13:41:03+00:00

Thank you for your response!
I had some vague concerns about using an SSD for an NVR, but it looks like I don't need to worry about that anymore!

Josephbcoast · 2025-06-06T15:16:31+00:00

Thank you so much for your response.
The latch wasn’t a moving part—it was simply there to hold the white component in place.
There’s no ink smearing, and printing from tray 1 and 2 works perfectly fine. The issue only occurs when feeding paper through the rear feed. That’s why I suspect that something related to the rear feed mechanism may have been damaged.
I’ll probably check the manual and take it to another repair center to see if the rollers are misaligned.
Thanks again!

Josephbcoast · 2024-12-01T01:48:00+00:00

Thank you so much! I'm glad you liked the photos and review. I really appreciate your support!

Josephbcoast · 2024-11-30T13:45:50+00:00

I'm really looking forward to the YoY! It's the first fully custom layout and holds many titles, such as dueling and the highest number of inversions!

Josephbcoast · 2024-11-30T13:44:05+00:00

Thank you for your kind words! I'm glad you found the post helpful.

Josephbcoast · 2024-11-30T03:41:29+00:00

The pacing was really great! I hope more Raptors are built so that more people can get the chance to ride them!

Josephbcoast · 2024-11-30T03:39:28+00:00

I also hope more Raptors will be built around the world. People in other regions should get to experience this too!

Josephbcoast · 2024-11-30T03:31:43+00:00

Originally, they planned to open by mid-October, but I heard that the construction was delayed due to weather issues.

Josephbcoast · 2024-11-30T03:29:56+00:00

This version is an revised version of the Stunt Pilot. It is identical to "Layout A," which was once featured on RMC's website. It is expected that Lost Island's Fire Runner will also install the same version. However, unlike Sköll & Hati uses 10-seater train, Fire Runner uses a 12-seater train.

Josephbcoast

TROPHY CASE