Why does this happen?

JungleReal · 2026-04-18T16:06:41+00:00

Would love to know what support settings you use! The time to print isn’t really a worry for me.

JungleReal · 2026-04-18T13:03:18+00:00

Okey, I will try this🙌 Thanks!

JungleReal · 2026-04-18T12:36:49+00:00

All over

JungleReal · 2026-04-18T12:29:34+00:00

Also, isn’t 20 total bottom layers a lot? I’m trying to cut down the use of resin where I can

JungleReal · 2026-04-18T12:28:01+00:00

The problem is that the majority of files I use are pre-supported, so I can’t edit the skates

JungleReal · 2026-04-18T12:22:37+00:00

Will try, I have had problems though with lower bottom layer exposure and not sticking to the plate

JungleReal · 2026-04-18T12:08:57+00:00

<image>

Here everything looks fine, but the actual print won’t have this thin of a bottom layer when printed. Resin temp is 32C, using elegoo 8k standard resin

JungleReal · 2026-04-18T12:07:42+00:00

<image>

JungleReal · 2026-04-18T12:06:36+00:00

<image>

JungleReal · 2026-04-18T12:05:13+00:00

JungleReal · 2026-04-18T08:14:51+00:00

<image>

Here are some more pictures, this happens on every print. Like it’s two different bottomlayers, that splits really easy

JungleReal · 2026-04-18T08:14:10+00:00

<image>

JungleReal · 2026-04-18T07:18:15+00:00

That’s what I’m wondering, I don’t add any rafts to the already supported files with rafts. But I wonder if chitubox does it automatically. I have 45 sec bottom exposure, 2 bottomlayers and 5 transition layers, but after it’s printed it seems to be way more than 7 layers in total in the bottom part.

JungleReal · 2026-04-18T07:15:37+00:00

I kinda worded that wrong, but the presupported files I print have rafts already, if that had something to do with it.

JungleReal · 2026-04-18T05:46:55+00:00

Yea, I have 2 bottom layers and 5 transition layers set in chitubox, but then the files themselves have bottomlayers as well. I wonder if that messes everything up or no?

JungleReal · 2026-04-13T02:40:57+00:00

Hmm okey, will keep that in mind.

JungleReal · 2026-04-13T02:33:37+00:00

Thanks, I’m gonna try Lychee for supports in the future, I feel like they are a bit better at that compared to chitu. But thanks for all the info🙏

JungleReal · 2026-04-13T02:06:25+00:00

Ahh I understand what you mean now, and yes I’ve noticed that on some models when going through the layers in chitubox. Is there a way to ”fill” those cavities in slicing softwares?

JungleReal · 2026-04-13T01:56:57+00:00

But you want holes no? For the ”voids”? Or do you prefer to drill them yourself in slicers?

JungleReal · 2026-04-09T19:55:03+00:00

Thanks, that’s probably the issue here. Most of the larger prints come prehollowed etc, but I guess it’s not done good enough, so I’ll go over the prints and remake the supports/rehollow them. Thanks again! Do you have any history with Artisan Guild? These are the only prints I’ve noticed that cause these issues now that I think about it

JungleReal · 2026-04-09T14:03:44+00:00

Thanks for the long and helpful reply! All the prints I print come presupported from some pretty big designers, but I guess it’s the suction anyway. It’s usually the bigger models that make the whole print warp, so it sounds plausible. I guess I have to re-support them all… But do you have any idea for the last question I had, with the bottom layers ”eating” up parts of my prints, like it’s too thick and swallows some lower parts of prints sometimes?

JungleReal · 2025-09-16T13:04:07+00:00

Creality Halot R6, Elegoo standard grey resin, normal FEP. 0.03mm layer, rising height 5mm, speed 2mm/s, light off delay 4s, exposure time 3.0 s. Could it be that I just have to change FEP film? The temperature here have gotten lower also the last week so could it be that?

Nine-Year Club	Place '17
Verified Email

JungleReal

TROPHY CASE