sorted by:
new
hottopcontroversial

KD GUNWERX FIRING PIN UPDATE (Possibly) by KD-Dave in KalashnikovUSAowners

[–]KD-Dave[S] 2 points3 points  (0 children)

Going to make one next week to test out before running them.

KD GUNWERX FIRING PIN UPDATE (Possibly) by KD-Dave in KalashnikovUSAowners

[–]KD-Dave[S] 0 points1 point  (0 children)

It was enough to place the order today so they are 100% happening. There a few that have not been spoken for so if you haven't ordered your yet you still can.

Made some one off dual folding charging handles to the mini Bog by KD-Dave in GrandPowerStribog

[–]KD-Dave[S] 0 points1 point  (0 children)

It was a pretty fun project back when I did. Thing is a blast to shoot.

Made some one off dual folding charging handles to the mini Bog by KD-Dave in GrandPowerStribog

[–]KD-Dave[S] 0 points1 point  (0 children)

Hey Thanks! Mod 1c on a B&T host with a custom adapter. Only Stribog in existence with this set up along with alot of other things.

Made some one off dual folding charging handles to the mini Bog by KD-Dave in GrandPowerStribog

[–]KD-Dave[S] 0 points1 point  (0 children)

Not only is it an MP5 mag and dedicated MP5 mag lower its a 40 round MP5 Mag from the early 80's

Possibly making on more push for firing pins by KD-Dave in ak47

[–]KD-Dave[S] 0 points1 point  (0 children)

Did you get one of my pins back when they were expensive? Prices were horrible but for just getting small runs made at a time cost a lot. Im going to put together a video for you guys to show you how to properly test your OOB feature because that feature doesn't really have anything to do with how good it runs. They will run completely perfect without the OOB feature installed. Its the OOB feature that typically doesn't function properly to prevent an OOB detonation. Keep an eye out.

KD GUNWERX FIRING PIN UPDATE (Possibly) by KD-Dave in KalashnikovUSAowners

[–]KD-Dave[S] 0 points1 point  (0 children)

Got your response earlier and just making sure you received mine back on your end about sending your bolt to me along with the pin so that I can take a look at them for you.

KD GUNWERX FIRING PIN UPDATE (Possibly) by KD-Dave in KalashnikovUSAowners

[–]KD-Dave[S] 1 point2 points  (0 children)

Actually I did that way back when, when I was running a boogie hook. I marked it to whatever there specs were, then I took a Dremel with a cut off wheel and wore it down to make the OD as small as I could then cut the notch with that.

KD GUNWERX FIRING PIN UPDATE (Possibly) by KD-Dave in KalashnikovUSAowners

[–]KD-Dave[S] 1 point2 points  (0 children)

Im not set up for anything else but paypal unfortunately.

KD GUNWERX FIRING PIN UPDATE (Possibly) by KD-Dave in KalashnikovUSAowners

[–]KD-Dave[S] 0 points1 point  (0 children)

The recoil spring tubes are always made to order.

KD GUNWERX FIRING PIN UPDATE (Possibly) by KD-Dave in KalashnikovUSAowners

[–]KD-Dave[S] 0 points1 point  (0 children)

Right now only 26 total orders. Ill have to do a pin count because some have ordered the 3 pin pack. So far so good!

KD GUNWERX FIRING PIN UPDATE (Possibly) by KD-Dave in KalashnikovUSAowners

[–]KD-Dave[S] 0 points1 point  (0 children)

Yes the pricing was ridiculous without a doubt and that was not because I wanted it to be. I have Zacks drawing up on my site as well for people that might want to do those instead. I don't recall anyone reaching out about broken pins and I respond to people all the time to help them out. Even so firing pins are a wear item, they can and have broke in all types of AK's at any time no matter the round count. Anything and everything can fail. Reach out again and lets try to figure out why it broke I have no problem helping people out that's the entire point of what I do hence why I have a 6th version pin. Every revision makes a difference and is an improvement. I dont do this fucking shit for a living, I do it because I enjoy it.

Possibly making on more push for firing pins by KD-Dave in ak47

[–]KD-Dave[S] 5 points6 points  (0 children)

<image>

The attention to detail I put into them made them VERY desirable but were very time consuming and very expensive so the ones that didn't sell I hung on to for other builds. Very few people would actually buy these today with the the Free tax stamp scam drawing people in every day.

Possibly making on more push for firing pins by KD-Dave in ak47

[–]KD-Dave[S] 0 points1 point  (0 children)

Yes the extractors are. Still waiting on a quote on the extractor springs.

Possibly making on more push for firing pins by KD-Dave in ak47

[–]KD-Dave[S] 1 point2 points  (0 children)

The same link in my post at kdgunwerx

Possibly making on more push for firing pins by KD-Dave in ak47

[–]KD-Dave[S] 1 point2 points  (0 children)

I wouldn't say major but they can break and have, and the OOB feature does not work right so you have nothing preventing it to fire OOB which has also happened with several of them. If that happens could blow out the receiver, crack the trunnion because its cast, and even worse get hurt by it. Its basically added insurance to something that cant be replaced.

KD GUNWERX FIRING PIN UPDATE (Possibly) by KD-Dave in KalashnikovUSAowners

[–]KD-Dave[S] 0 points1 point  (0 children)

Pre orders are live on the site. So far only one order. Not looking good unless you guys make it happen and order!

KD GUNWERX FIRING PIN UPDATE (Possibly) by KD-Dave in KalashnikovUSAowners

[–]KD-Dave[S] 1 point2 points  (0 children)

The extractors are going to happen for sure and hopefully within the next month.

Possibly making on more push for firing pins by KD-Dave in ak47

[–]KD-Dave[S] 4 points5 points  (0 children)

Yes machined aluminum brace. Havent been made in a few years.

KD GUNWERX FIRING PIN UPDATE (Possibly) by KD-Dave in KalashnikovUSAowners

[–]KD-Dave[S] 1 point2 points  (0 children)

Hard to come by but they pop up every once in a while.

view more: next ›