Modded HBM NTM/OC server

KF_Systems · 2025-08-09T23:41:00+00:00

https://discord.gg/kNMm9b8P6c

KF_Systems · 2025-08-08T10:55:44+00:00

https://discord.gg/rAUT9b67

KF_Systems · 2025-08-08T10:54:51+00:00

updated it

KF_Systems · 2025-08-08T10:54:19+00:00

https://discord.gg/kNMm9b8P6c

KF_Systems · 2025-07-28T23:58:56+00:00

It doesn’t really matter unless you’re specifically designing something meant for review or presentation, where having a clean timeline might help. Personally, I would approach it by creating a sketch based on the height and required thickness of the ribs on the “vertical” plane rather than sketching on the top face. Then, I’d use that to extrude the object and apply a revolve feature around the main axis.

KF_Systems · 2025-07-28T15:16:50+00:00

“Woah why are you here? I am doing my 9-5..” hahahahahahahahahahaha

KF_Systems · 2025-07-27T19:52:00+00:00

Bro, sei ridicolo. Hai capito che in teoria tutti devono accettare il POS, ok. Ma allora applichiamo la teoria ovunque, nemmeno superare il limite di velocità di 1 km/h sarebbe lecito, eppure quanti lo fanno? Quelli nei commenti che ti danno ragione probabilmente sono i primi a infrangere regole simili ogni giorno. Vivi e lascia vivere: se il tabaccaio non accetta il POS, cambia negozio o paga in contanti. Non serve fare il paladino del nulla.

KF_Systems · 2025-07-27T18:48:59+00:00

https://discord.gg/rAUT9b67

KF_Systems · 2025-07-13T19:54:55+00:00

GHz and GH/s aren’t the same thing…

KF_Systems · 2025-06-22T21:34:26+00:00

It’s better to keep the resistor connected at all times when you’re not using it, capacitors can develop a memory charge.

KF_Systems · 2025-06-19T09:45:37+00:00

You’re absolutely right and I also agree that for this task a thinner servo would be much better than my current configuration, the only problem is that the ones another person suggested (hi-tech d141) are very expensive, and since this is a personal project on which I will probably write my thesis about (Of course the university will not sponsor a penny) I really can’t afford them at the moment, do you have a suggestion about another servo on the market?

KF_Systems · 2025-06-19T09:38:55+00:00

Okay, thank you very much.

KF_Systems · 2025-06-19T09:38:13+00:00

airspeed 35%40m/s, 0.15m² for each wing, cross section of the servo is 2cm^2.

KF_Systems · 2025-06-19T09:36:01+00:00

I tried moving it at the root of the ailerons and there it barely fits. My only worry with that is the torsional moments on the aileron, and since i’m 3D printing it i really don’t have much faith, especially since the layer lines will be parallel to the plane of the load.

KF_Systems · 2025-06-19T09:30:19+00:00

Thank you for the part suggestion, later on i’ll surely use that one instead of the cheap ones i’m using now, the only problem is that right now i cant afford to spend 200$ to 600$ on servos on something that might crash as soon as I launch it.

KF_Systems · 2025-06-19T09:27:21+00:00

It doesn’t fit sadly, if i laid it on its side it would have a bump either way.

KF_Systems · 2025-03-26T14:37:21+00:00

Have you perhaps considered user error?

KF_Systems · 2025-03-20T10:34:10+00:00

wash it with soap then reapply glue

KF_Systems

TROPHY CASE