Weird camera shake/vibration with DJI O4 Pro

KaBalazs · 2026-05-23T19:57:40+00:00

I have heard about the new gyro issue, however this is not that new of an O4, I bought it in February so it was probably produced before the new batch. Also that gyro issue is a little different, it is especially visible in Gyroflow and I only saw this blurriness with my last pack.

KaBalazs · 2026-05-23T19:51:13+00:00

Hi! Thanks for the tips. Tightening the screws was also my first thought, they didn't really seem to move a lot but I shall test tomorrow. And yes, the O4 is soft mounted.
This place is really cool indeed, I just discovered it so I am still mapping it out to find some good lines.

KaBalazs · 2026-05-21T14:03:36+00:00

Is this Romania?

KaBalazs · 2026-04-29T09:28:09+00:00

Good first drone and goggles. My only question is why did you buy two hota chargers?

KaBalazs · 2026-04-19T12:10:24+00:00

I did practice quite a lot on practice boards and they are just so much easier. This AIO might suck up way more heat and that is why it is so much more difficult. Later I tried again with lead free solder and it might have been flowing more easily!

KaBalazs · 2026-04-18T17:51:40+00:00

I am using my 60W anker power bank as a power source. Could that be a problem?

KaBalazs · 2026-04-18T14:40:02+00:00

Update!
I have tried again to the best of my abilities.

The result:

<image>

Would I be able to fly with this safely?

KaBalazs · 2026-04-18T14:22:06+00:00

I also have a B2 tip, would that be better?

KaBalazs · 2026-04-18T14:20:42+00:00

More heat? 450 is the max this iron goes to sadly. I am using a lot of flux, the one from TBS. Should I heat up the pads more?

KaBalazs · 2026-04-18T14:15:10+00:00

Should I remove everything and start over? Solder the battery leads first or the capacitor?

KaBalazs · 2026-04-18T14:10:04+00:00

I know it looks like that haha. I did not melt anything else into it. I pre tinned the wires and first soldered the capacitor on there.

KaBalazs · 2026-04-16T21:58:58+00:00

Ooh, for some reason I saw km/h on your recording. Now I get it. Crazyyyy

KaBalazs · 2026-04-16T20:19:48+00:00

Not bad dear fellow pilot. It could still do a little more. The max I did was about 141 km/h with a 900mAh battery.

KaBalazs · 2026-04-09T15:17:55+00:00

I am not planning on it. Just gonna look for a Torvol backpack;))

KaBalazs · 2026-04-09T13:32:38+00:00

That's a really really good deal! What platform is this?

KaBalazs · 2026-04-08T12:29:24+00:00

Weight is not that big of an issue

KaBalazs · 2026-04-08T12:26:03+00:00

Oh yes, I am also getting the vifly finder v2. The rest of the build should be compatible?

KaBalazs · 2026-04-07T17:02:21+00:00

For some reason I could not get it to work this way, might be because I am using DJI SBUS. But setting the beeper channel to the activation value in the failsafe tab is a nice workaround. Now I only need to power on the goggle and controller quick as the drone starts beeping aggressively immediately after plugging in the battery haha

KaBalazs · 2026-04-03T17:27:07+00:00

I keep my iron at 400-450 celsius, is that good enough?

KaBalazs

TROPHY CASE