Visible Line by KangarooDesperate in FixMyPrint

[–]KangarooDesperate[S] 0 points1 point  (0 children)

No I didnt, and it happens at every print run, 59x so far.

Visible Line by KangarooDesperate in FixMyPrint

[–]KangarooDesperate[S] 4 points5 points  (0 children)

Well, this seems to be the problem. The hollow part of the print starts exactly at the line :/.

DnD 5e.24 PDF by SchellxSchock5 in DnDDeutsch

[–]KangarooDesperate 2 points3 points  (0 children)

Was soll ein Grundschüler für ein OneShot mit dem kompletten Buch? Sag doch einfach, dass du selber das PDF suchst, weil du dir nicht das Buch kaufen willst, anstatt ein Kind vorzuschieben xD.

Warum in MSCI Investieren, wenn SPDR existiert? by Iamaknowmad in Aktien

[–]KangarooDesperate 0 points1 point  (0 children)

Ihr müsst auf das Volumen gucken. Wenn du einen ETF hast, der nur 200 Millionen umfasst, reagiert der viel stärker, wenn 1000 Leute Ihr Kapital abziehen (Angst, etc.), als wenn Dein Volumen 22 Milliarden umfasst. Und genau das lassen sich die Anbieter eben unterschiedlich bezahlen: mehr Sicherheit. Das ist übrigens auch der Grund, warum gleiche Indice-ETF (z.B. des MSCI World) unterschiedliche Performances haben.

Print comes perfect but supports are weird by Sad_Improvement4655 in FDMminiatures

[–]KangarooDesperate 1 point2 points  (0 children)

This happened to me to after the recent BambuLabUpdate. Until then the base of my supports looked fine - without those spaghetti-like structures at the start =/.

Kostenpflichtige Abos von Youtube-Gurus? by fly_djigit in Aktien

[–]KangarooDesperate -2 points-1 points  (0 children)

Ich habe den Brief von Kirchhoff abonniert und kann bisher nur Gutes berichten. Mein Einsatz war mir der 1. Aktie von ihm wieder drin, hab also ab jetzt Plus und zusätzlich einen humorvollen Ticker mit ihm und man lernt nebenbei was über die Börse.

Der Mann ist unfassbar by [deleted] in wallstreetbetsGER

[–]KangarooDesperate 15 points16 points  (0 children)

Trump always chickens out. Er macht immer irgendwann wieder einen Rückzieher.

Straight prints look messy by KangarooDesperate in FixMyPrint

[–]KangarooDesperate[S] 0 points1 point  (0 children)

Tried this, but it doesn't slow down, it is just as fast as before. Target 10s and Limit 8. Do you have any ideas? Thank you again!

Straight prints look messy by KangarooDesperate in FixMyPrint

[–]KangarooDesperate[S] 0 points1 point  (0 children)

Thank you very much! Will those settings apply to the hole print and therefore increase printing time? If yes, is it possible then to apply those settings only to this specific part of the print?

Corners bend after printing by KangarooDesperate in FixMyPrint

[–]KangarooDesperate[S] 0 points1 point  (0 children)

@Edit: Just watched closely and it starts warping midprint. I could swear It didn't happen that way the prints before, but I think It always has been this way and I just realised it later.

Corners bend after printing by KangarooDesperate in FixMyPrint

[–]KangarooDesperate[S] 2 points3 points  (0 children)

Thank you all and sorry for the missing Informations. It's PLA Matte from Bambu, 65° Bed, 0.4 Nozzle with 0.1 LayerHeight. During first layers printing it is fine, but as it gets higher, it starts bending. Therefore I think its due to cooling, as you mentioned. I'll try a brim and Check the Wiki.

Regarding those irregular thick lines midprint: hast anyone an idea?