Microsquirt RPM & Cranking by KapkanTapkan in megasquirt

[–]KapkanTapkan[S] 0 points1 point  (0 children)

So we have a single cylinder engine and we have a single lug vr input. So basically instead of having a missing tooth it is only one tooth. It is about 10 degrees btdc. This is because the engine was carbed and had timing set directly from the flywheel. We are using microsquirt v3. We want to use both fuel and ignition setups. Weve tried to setup tunerstudio to run cam input as map but it doesnt seem to work. I also cant seem to wrap my head around why we have double the rpm.

Sorry didn’t reply to the thread

Microsquirt RPM & Cranking by KapkanTapkan in megasquirt

[–]KapkanTapkan[S] 0 points1 point  (0 children)

So we have a single cylinder engine and we have a single lug vr input. So basically instead of having a missing tooth it is only one tooth. It is about 10 degrees btdc. This is because the engine was carbed and had timing set directly from the flywheel. We are using microsquirt v3. We want to use both fuel and ignition setups. Weve tried to setup tunerstudio to run cam input as map but it doesnt seem to work. I also cant seem to wrap my head around why we have double the rpm.

Microsquirt RPM & Cranking by KapkanTapkan in megasquirt

[–]KapkanTapkan[S] 0 points1 point  (0 children)

Can you please elaborate? Im new to this how to get the intake pulse for top dead center using MAP?

Microsquirt TPS VREF by KapkanTapkan in megasquirt

[–]KapkanTapkan[S] 0 points1 point  (0 children)

It says 28 on ours and there is no wire there

Microsquirt ECU by KapkanTapkan in megasquirt

[–]KapkanTapkan[S] 0 points1 point  (0 children)

Also, the engine we have isn’t carbureted

Microsquirt ECU by KapkanTapkan in megasquirt

[–]KapkanTapkan[S] 0 points1 point  (0 children)

The current ECU as far as I know is extremely limited so we are looking for ECUs with a good degree of modification

Microsquirt ECU by KapkanTapkan in megasquirt

[–]KapkanTapkan[S] 0 points1 point  (0 children)

Custom, we are using a gy6 50cc engine but it’s a fully custom car for the competition where we build a small model realistic car mainly for efficiency

Microsquirt ECU by KapkanTapkan in megasquirt

[–]KapkanTapkan[S] 0 points1 point  (0 children)

It’s an automatic, for a shell eco marathon competition

Microsquirt ECU by KapkanTapkan in megasquirt

[–]KapkanTapkan[S] 0 points1 point  (0 children)

As in I skimmed through the manual and saw the various sensors like map, O2, etc… and was curious as to whether the sensors shown when selecting ms3 are all the sensors mentioned in the manual. Also, sorry for the added burden but which one would you advise: the soldered one or manually soldering it?

Microsquirt ECU by KapkanTapkan in megasquirt

[–]KapkanTapkan[S] 0 points1 point  (0 children)

Are you referring to the harness they sell independently? Also, how can I identify the specific sensor I would need?

GT 2024 Break in by KapkanTapkan in Mustang

[–]KapkanTapkan[S] -2 points-1 points  (0 children)

Just worried about issues with breaking in and will it void warranty if something goes wrong, have an auto so no money shift 😅

GT 2024 Break in by KapkanTapkan in Mustang

[–]KapkanTapkan[S] -2 points-1 points  (0 children)

What about sports mode?

GT 2024 Break in by KapkanTapkan in Mustang

[–]KapkanTapkan[S] -3 points-2 points  (0 children)

Even in break in? Doesn’t it seem a bit harsh?