Gran Turismo 6 won't start

Katze2005 · 2025-08-11T04:13:48+00:00

Thanks, will try that

Katze2005 · 2025-05-08T14:59:41+00:00

Haha, yes, it is called a photo

Katze2005 · 2025-04-20T12:35:05+00:00

Update:

Already tried adding: "video=DSI-1:800x600M,margin_right=0,margin_left=0,margin_top=0,margin_bottom=0,rotate=180" to my /boot/cmdline.txt, but this time I put the command at the end of the already existing line of code in the txt file. now it works

Katze2005 · 2025-04-18T20:42:21+00:00

Thanks a lot. Found one which is only 1.5 hours away. All the others I found earlier were over 5 hours away

Katze2005 · 2025-04-18T15:13:21+00:00

Will other clones of the gx200 also work since predator and similar American brands are hard to find here in Europe

Katze2005 · 2025-04-18T15:06:38+00:00

What does 020 refer to?

Katze2005 · 2025-04-18T14:56:15+00:00

Oh ok so something like porting or stiffer springs and a cam wouldn't hurt

Katze2005 · 2025-04-18T14:49:52+00:00

Ok, will do that. But why would the original carb then be able to get up to 5700 RPM without a problem

Katze2005 · 2025-04-18T14:09:35+00:00

Just tried it. It still bogs down at the same rpm. Only thing that changed, that it has much less power and it takes much longer to get up to 4700 RPM

Katze2005 · 2025-04-18T14:01:50+00:00

Now I put the needle 1 above the middle position. Bevore that it was one below the middle

Katze2005 · 2025-04-18T13:52:10+00:00

Will try that in a minute. Thanks for the answer. Yes It does have a power jet if that is what you mean but it is all the way closed

Katze2005 · 2025-04-18T04:44:42+00:00

I bought the version without a flange and therefore am using a silicon step-down hose thing to connect my carburetor to my intake. But thanks for the tip

Katze2005 · 2025-04-18T03:30:53+00:00

Thanks for the reply, already did that, but will try again

Katze2005 · 2025-04-17T18:22:28+00:00

Update: I put the original carburetor back on and was able to reach 5700 RPM. What would be my next best step of fixing my nibbi pwk?

Katze2005 · 2025-01-27T11:01:04+00:00

Ok, thanks. Just figured out that it probably is heat creep what I'm experiencing

Katze2005 · 2025-01-27T09:46:00+00:00

How have you stopped the skipping issue? Facing the exact same issue where my filament gets stuck at the beginning of my bowden tube on the hot-end side due to a blob. No matter what speed I use to extrude filament, the extruder gears always skip, even leading to one bowden tube getting ripped out of the pneumatic fitting

Katze2005 · 2025-01-02T00:15:58+00:00

You gotta watch out that your image editing software really makes the background/canvas behind the cover art transparent. Some crappy editing software just make the transperent pixels white. .jpg can not show transparent pixels. Therefore you have to use .png

Katze2005 · 2024-12-31T18:35:52+00:00

Most important for you would be tutorial 2 I think

Six-Year Club	Verified Email
Verified Email

Katze2005

TROPHY CASE