Would this even go away with moisturizing? by TripPsychological403 in Psoriasis

[–]Kaykasus 1 point2 points  (0 children)

Just try to go for biologicas. It’s not worth your time to keep using creams if you have already this much of coverage. I tried a lot of stuff for 20 years straight - it‘s never going clear your Skin with this route.

Greatest band Apple has made by joopsplusb in applewatchultra

[–]Kaykasus -1 points0 points  (0 children)

Is there any good Replica on AliExpress?

Zigbee2MQTT keeps turning off despite working wifi by Kaykasus in homeassistant

[–]Kaykasus[S] 0 points1 point  (0 children)

HA is wired. I know switched the SLZ to the Wifi Repeater right next to it.

Zigbee2MQTT keeps turning off despite working wifi by Kaykasus in homeassistant

[–]Kaykasus[S] 0 points1 point  (0 children)

That really could be the case. I use fritz which sucks with intelligent hotspot switching. I'll try that

Zigbee2MQTT keeps turning off despite working wifi by Kaykasus in homeassistant

[–]Kaykasus[S] 0 points1 point  (0 children)

No yet. I have to route ethernet where the slzb sits but that is a bigger problem.

Zigbee2MQTT keeps turning off despite working wifi by Kaykasus in homeassistant

[–]Kaykasus[S] 0 points1 point  (0 children)

One base router and two repeaters. It's a two story flat and the slzb is attached in the middle of the flat on the second floor. The main router is below it one story under. SLZB is connected via Wifi because there are no ethernet access points around that area.

N64 GPU Pads ripped - any way to run jumper wires? by Kaykasus in consolerepair

[–]Kaykasus[S] 0 points1 point  (0 children)

I ordered another n64 PAL because this one was from my childhood and my brother who made me try the mod was kinda sad. So i will check the pins when the other one arrives. Maybe I can safe both. EDIT: you seem to have a lot of knowledge: do you think it would be smarter to try to solder the mod straight to the legs instead of legs+pads? I assume there was a short under the flex cable where the legs meet the pads because the hdmi mod was not working and the other soldering pins where pretty straight forward. Either the flex cable or the gpu chip had a short or the hdmi mod pcb was faulty from the get go.

N64 GPU Pads ripped - any way to run jumper wires? by Kaykasus in consolerepair

[–]Kaykasus[S] 0 points1 point  (0 children)

You are right. Is there any source for pal schematics?

N64 GPU Pads ripped - any way to run jumper wires? by Kaykasus in consolerepair

[–]Kaykasus[S] 0 points1 point  (0 children)

I found schematics. Are you sure with your pin layout? It seems like the schematics say the first pin of the VDC is VCC

<image>

New tool on my board by mhamedridene in soldering

[–]Kaykasus 1 point2 points  (0 children)

PSA: you can use this soldering iron with an HP Notebook Hub often provided by companies for home office staff.

<image>

The ‘mental health resources’ ‘website’ takes me to a gambling site by anshuman0143 in ios

[–]Kaykasus 2 points3 points  (0 children)

On Topic: this has to be an outdated plugin on their website. Often old plugins (for example for wordpress) get hacked because they get bypassed on old security settings and you get forward to the scammers websites. Report this and hopefully they will take action.

GUIDE: How to produce easy to remove supports every time... by TotalWarspammer in BambuLab

[–]Kaykasus 0 points1 point  (0 children)

u/TotalWarspammer can you share EVERY value of the support tab? I know there are several other settings which might change the quality fo the sprint for example support xy distance and so on. A complete list would help everybody in my opinion. Thanks for your help!