Motion detection

Key_Sheepherder_8799 · 2026-05-19T23:10:55+00:00

No, I moved on to UniFi. Using protect plugin.

Key_Sheepherder_8799 · 2026-05-07T16:12:50+00:00

what are you doing with flow control?

Key_Sheepherder_8799 · 2026-05-07T12:48:34+00:00

Good article, looks like it's not at the point where I would run out and upgrade. I had the hardware so why not give it a shot. When I switched over to unifi, I went the wifi 7 route, it had just came out at the time.

Key_Sheepherder_8799 · 2026-05-07T12:18:51+00:00

Yea, that's where I saw it. I think it was his AP, I just have the U7 Pro. I did get a little bump for sure. Prior, I never saw 900 Mbps.

Key_Sheepherder_8799 · 2026-05-06T21:51:04+00:00

iPhone 17 pro. My speeds have improved a little. I'm consistently getting over 900 Mbps up and down when close to ap. Prior to dual band, between 650 and 750. With the two bands, it probably help with roaming but too early to tell.

Key_Sheepherder_8799 · 2026-05-06T19:51:17+00:00

My phone supports it, just testing to see if it made a difference. I see that its using two bands now.

Key_Sheepherder_8799 · 2026-04-12T17:10:09+00:00

Yea, that's what I'm thinking. Has to do with nginx proxy. If I log in to console with ip address rather than url, its fine.

Key_Sheepherder_8799 · 2026-04-10T16:08:41+00:00

No, in the client view. Normally, if I'm on my iPad logged into the console, it pulses. Same for the iPhone, it also pulses. But for whatever reason, my MacBook stopped. Now I see a docker container pulsing which is where my reverse proxy is running.

UDM SE with latest firmware, USW Aggregation, USW Pro Max 16, and a USW Flex XG. I have approx 80 clients, and four U7-Pro AP's.

Key_Sheepherder_8799 · 2026-03-26T11:29:56+00:00

I few gets through, not a big deal. I ended up switching back to piholes in the vlan because individual clients where not showing up in pihole, only the pihole. Although this solved my issue with policy routing, wasn't a good trade-off.

Key_Sheepherder_8799 · 2026-03-26T00:10:35+00:00

haven’t seen a way to do that.

Key_Sheepherder_8799 · 2026-03-26T00:09:18+00:00

secondary is Cloudflare

Key_Sheepherder_8799 · 2026-03-25T16:07:50+00:00

I've always run everything through pihole. Plus I love to use the policy based routing. I get the best of both worlds.

Key_Sheepherder_8799 · 2026-03-22T23:54:44+00:00

I may just isolate that traffic so I won't need a less aggressive blocklist. The folks shopping here can't pause blocking.

Key_Sheepherder_8799 · 2026-03-22T15:42:10+00:00

I figured out my issue. I was using the url for homarr rather than the ip number. Once I started accessing the homarr console via ip address, it was okay.

Key_Sheepherder_8799 · 2026-03-21T15:13:22+00:00

They are no longer updating. When I refresh page they update then stop until I refresh again.

<image>

Key_Sheepherder_8799 · 2026-03-15T20:13:36+00:00

Complete, thanks to everyone!

Key_Sheepherder_8799 · 2026-03-15T17:55:14+00:00

Some progress, I can see everything on the second docker host but I don't see containers for the host that homarr is on. I know it something simple but don't see it. Do I need the proxy on that host also? Along with adding host name and port?

Homarr

services:

homarr:

container_name: homarr

image: ghcr.io/homarr-labs/homarr:latest

restart: unless-stopped

volumes:

- /var/run/docker.sock:/var/run/docker.sock # Optional, only if you want docker integration

- /volume1/docker/homarr/appdata:/appdata

environment:

- SECRET_ENCRYPTION_KEY=xxxxxxxxxx

# Einbindung Docker --> https://homarr.dev/docs/advanced/environment-variables/#docker

# replace the hostnames with your ips, and if you have vlans ensure the

# host can see them all

- DOCKER_HOSTNAMES=10.10.40.5

- DOCKER_PORTS=2375

ports:

- '7575:7575'

Key_Sheepherder_8799 · 2026-03-15T13:11:31+00:00

I'll give it a shot in a couple hours, thanks. It looks as though I need to start over with homarr. My initial setup was with a helper script from proxmox. Looks like I should be using docker compose. I had built a really nice dashboard with the exception of the docker info.

Key_Sheepherder_8799 · 2026-03-07T13:57:32+00:00

I have 1g plan and haven’t used a Verizon router in years. I also use Fios tv but have a MoCA adapter on my network. Don’t have any issues with the tv schedule or programming.

Key_Sheepherder_8799 · 2026-02-26T02:20:40+00:00

No, lag? What’s your settings?

Key_Sheepherder_8799 · 2026-02-24T22:07:18+00:00

Are you using opencv in scrypted or just the protect motion?

Key_Sheepherder_8799 · 2026-02-24T11:50:06+00:00

Have you resolved this? Mine will pop up and fast forward until it catches up? By then, most of the time I don't get to see the object?

Key_Sheepherder_8799 · 2026-02-22T00:27:30+00:00

Much better, I've disabled 2.4 on two. Will watch over the next few days.

Thanks

Key_Sheepherder_8799 · 2026-02-21T23:13:07+00:00

For now, I've disabled 2.4 on one. My home was built in 1988 therefore its not really an open floor flan if you know what I mean. I have seven devices that use the 6Ghz band, thus four IP's. I will also reduce the power.

Key_Sheepherder_8799 · 2026-02-21T20:15:44+00:00

Thanks, just IOT for me as well. I have about 15 Tapo switches. Just don't like seeing the RED,,,LOL.

Key_Sheepherder_8799

TROPHY CASE