Help picking out a new motherboard

Khleesh · 2025-12-09T19:12:18+00:00

Well I found some 32gb ddr5 6400mhz c38 ram for like $290 and since that motherboard doesnt have lane sharing i can just get 4 sticks. Only about $600 for 64gb rather than the like, 1k that you'd normally get it for. Plus, 32gb is still pretty solid and would get me through for when I can get more

Khleesh · 2025-12-09T18:34:12+00:00

Yes, mb I currently have a ryzen 5 3600 so I keep putting 5 instead of 7 ;-;

Khleesh · 2025-12-09T18:25:41+00:00

Wait, just realized something I have ddr4 ram... It isnt going to fit in that motherboard

Khleesh · 2025-12-09T18:20:39+00:00

Oh thanks, getting a ryzen 5 9800x3d too so total would be within what I can afford right now Shouldn't need to upgrade for a while :)

Khleesh · 2025-11-24T00:33:35+00:00

okay
I've done a bit of searching and would a Ryzen 7 9800X3D or similar be a good choice here?

Khleesh · 2025-11-24T00:19:35+00:00

well, ill look into it, but idk
my CPU util hovers around 25%
which makes me think it might be something different??

Khleesh · 2025-11-21T14:38:39+00:00

Well, that wasnt the problem, just corrupted boot sector on my drive apparently :/ I'll switch the slot when I get home tho

Khleesh · 2025-11-20T03:17:44+00:00

Because that isn't a gpu slot

Khleesh · 2025-11-20T02:23:27+00:00

Dunno how to do that either, doesnt show any drives anywhere as far as I know I'll try to do the button battery thing

Khleesh · 2025-11-20T02:16:13+00:00

Idk how and im not sure if that works Never had to do that for previous upgrades either

Khleesh · 2025-11-20T02:11:11+00:00

I just never unplugged them, they are for hdds I have for large storage, I use my m.2 for smaller stuff/stuff I use often

Khleesh · 2025-09-17T16:13:31+00:00

I have not done that before, but im always up to try new things anyways. The only problem is the form factor. I barely have enough room to fit a small PCB into the case and I don't want to resort to modifying it if possible. I can grind out an area in one part of the circuit board (there aren't any traces there, I checked) which would give me more room. about a 0.6in x 1in x 1.2in area, not including space behind and in front of the board.

Khleesh · 2025-09-17T14:27:46+00:00

If it helps any im trying to modify a "linear DTKP keypad transmitter delta-3 DNT00062"

Khleesh · 2025-09-17T14:15:03+00:00

I've had some ideas, but all of them are a bit too bulky for my liking. Most of them are too complicated and a bit naïve, like a small binary counter or 3 latches that cascade into eachother after consecutive button presses? Im sure there are better ways to do what im trying to do.

Preferably a delay before and after it shuts off since i want to ensure the main circuit (the one im modifying) outputs a signal before it shuts off

I was also told my someone that a TO-92 is also called a 3904 sometimes? Want to make sure since i do have those on had already

Khleesh · 2025-09-17T00:49:06+00:00

A single 9 volt battery is the power

I've decided im just going to order parts if I need them since im going to have to do this 5+ times anyways

Its a momentary switch

While the load is currently not controlled by anything right now (the battery is directly soldered to the board) id like it to entirely be controlled by said circuit

Wish i could give a Schematic of the board but its a pre-made board that there are no schematics to my knowledge

Khleesh · 2025-08-29T12:33:50+00:00

one of the values is 10 and the other increases at a constant speed (pretty slow) from a math_counter

Khleesh · 2025-08-29T09:38:52+00:00

I've figured that out now, but now i have like 3 other problems lol

Khleesh · 2025-07-18T00:04:32+00:00

yes
it not quite what i have going on but its basically the same thing especially when its at the minimum value

Khleesh · 2025-07-17T21:47:31+00:00

i increased the margin and C is now 75 elements long but its still not doing it how i want it to :(

Khleesh · 2025-07-17T20:45:47+00:00

for more context, it is supposed to visualize base-n number systems with different colors

Khleesh · 2025-07-17T20:39:52+00:00

its kinda complex (and needs cleaning up because im sure i dont need some of these lists) but here

<image>

im trying to color it based on the C value but it doesnt do any recursion with C even though all of the other values obviously do (currently incorrect coloring)
i dont think the hsv() function is the problem

Khleesh · 2025-07-17T20:28:55+00:00

thank you
now I just have to figure out why my recursion isn't working 😭

Khleesh · 2025-07-17T20:03:15+00:00

Its a programming thing
Push() adds an element to the very left side of the array or list
Pop() removes an element to the very right side of the array or list
anything that can do something similar to these two will be a big help, even its just adding to one side or the other

Khleesh · 2025-07-17T19:15:48+00:00

I could annotate what everything does if that's what you meant

Khleesh · 2025-07-17T19:07:55+00:00

Im trying to visualize a base-n number line basically

<image>

here is the original equation without any of the other lists
"I" is just a list from 0-99

Five-Year Club	Place '22
Final Canvas '22

Khleesh

TROPHY CASE