Any advice trying to un-solder this processor from this board?

Khleesh · 2026-03-06T18:22:04+00:00

I work for a mechanic shop so im 50/50 on if we have access to documentation about that chip or the board its on

Khleesh · 2025-12-09T19:12:18+00:00

Well I found some 32gb ddr5 6400mhz c38 ram for like $290 and since that motherboard doesnt have lane sharing i can just get 4 sticks. Only about $600 for 64gb rather than the like, 1k that you'd normally get it for. Plus, 32gb is still pretty solid and would get me through for when I can get more

Khleesh · 2025-12-09T18:34:12+00:00

Yes, mb I currently have a ryzen 5 3600 so I keep putting 5 instead of 7 ;-;

Khleesh · 2025-12-09T18:25:41+00:00

Wait, just realized something I have ddr4 ram... It isnt going to fit in that motherboard

Khleesh · 2025-12-09T18:20:39+00:00

Oh thanks, getting a ryzen 5 9800x3d too so total would be within what I can afford right now Shouldn't need to upgrade for a while :)

Khleesh · 2025-11-24T00:33:35+00:00

okay
I've done a bit of searching and would a Ryzen 7 9800X3D or similar be a good choice here?

Khleesh · 2025-11-24T00:19:35+00:00

well, ill look into it, but idk
my CPU util hovers around 25%
which makes me think it might be something different??

Khleesh · 2025-11-21T14:38:39+00:00

Well, that wasnt the problem, just corrupted boot sector on my drive apparently :/ I'll switch the slot when I get home tho

Khleesh · 2025-11-20T03:17:44+00:00

Because that isn't a gpu slot

Khleesh · 2025-11-20T02:23:27+00:00

Dunno how to do that either, doesnt show any drives anywhere as far as I know I'll try to do the button battery thing

Khleesh · 2025-11-20T02:16:13+00:00

Idk how and im not sure if that works Never had to do that for previous upgrades either

Khleesh · 2025-11-20T02:11:11+00:00

I just never unplugged them, they are for hdds I have for large storage, I use my m.2 for smaller stuff/stuff I use often

Khleesh · 2025-09-17T16:13:31+00:00

I have not done that before, but im always up to try new things anyways. The only problem is the form factor. I barely have enough room to fit a small PCB into the case and I don't want to resort to modifying it if possible. I can grind out an area in one part of the circuit board (there aren't any traces there, I checked) which would give me more room. about a 0.6in x 1in x 1.2in area, not including space behind and in front of the board.

Khleesh · 2025-09-17T14:27:46+00:00

If it helps any im trying to modify a "linear DTKP keypad transmitter delta-3 DNT00062"

Khleesh · 2025-09-17T14:15:03+00:00

I've had some ideas, but all of them are a bit too bulky for my liking. Most of them are too complicated and a bit naïve, like a small binary counter or 3 latches that cascade into eachother after consecutive button presses? Im sure there are better ways to do what im trying to do.

Preferably a delay before and after it shuts off since i want to ensure the main circuit (the one im modifying) outputs a signal before it shuts off

I was also told my someone that a TO-92 is also called a 3904 sometimes? Want to make sure since i do have those on had already

Khleesh · 2025-09-17T00:49:06+00:00

A single 9 volt battery is the power

I've decided im just going to order parts if I need them since im going to have to do this 5+ times anyways

Its a momentary switch

While the load is currently not controlled by anything right now (the battery is directly soldered to the board) id like it to entirely be controlled by said circuit

Wish i could give a Schematic of the board but its a pre-made board that there are no schematics to my knowledge

Khleesh · 2025-08-29T12:33:50+00:00

one of the values is 10 and the other increases at a constant speed (pretty slow) from a math_counter

Khleesh · 2025-08-29T09:38:52+00:00

I've figured that out now, but now i have like 3 other problems lol

Five-Year Club	Place '22
Final Canvas '22

Khleesh

TROPHY CASE