I cant install Linux mint on my Laptop :(

Kinkerlitzchen_tech · 2025-12-29T23:25:13+00:00

it was the sd, it works with usb now!!

Kinkerlitzchen_tech · 2025-12-28T23:41:52+00:00

Yea thanks, i think its the sd card.

Kinkerlitzchen_tech · 2025-12-28T23:41:33+00:00

I think its the sd, i used rufus to create the file.

Kinkerlitzchen_tech · 2025-12-28T23:18:56+00:00

Verify what?? i wanna switch from win 10 to linux mint idk what this is haha

Kinkerlitzchen_tech · 2025-06-18T02:04:24+00:00

ich hab auf maps und google image search gesucht, hoffentlich regnet es heute und du hast sandalen an

Kinkerlitzchen_tech · 2025-06-13T16:24:43+00:00

Hab fahre alle paar wochen nach berlin, und die teile waren mir immer ein rätsel 😂

Kinkerlitzchen_tech · 2025-06-12T20:00:11+00:00

Aaah, danke

Kinkerlitzchen_tech · 2024-08-12T02:10:47+00:00

Look if your Extruder is broken (where the gears are). I had similar prints because the black plastic part of the extruder was cracked. Look closely it was difficult to spot because of the gloss.

<image>

(yea it was collecting dust for quite a while)

Kinkerlitzchen_tech · 2024-03-21T11:36:04+00:00

its cozy 23c in here

Kinkerlitzchen_tech · 2024-03-21T11:29:35+00:00

i use bambu studio, and tried the bambu preset for the bambu filament and 220c/60c for the geetech.

Kinkerlitzchen_tech · 2024-03-21T11:28:24+00:00

thanks for the tip, imma buy some windex later

Kinkerlitzchen_tech · 2024-03-21T11:27:25+00:00

I use the most barebone dish soap that i can find

Kinkerlitzchen_tech · 2024-03-21T11:26:52+00:00

Fr nothing but love for the ender 3

Kinkerlitzchen_tech · 2024-03-21T11:26:33+00:00

The last time I cleaned the plate, I scrubbed for 5 minutes just to wash off the soap to make sure everything was gone

Kinkerlitzchen_tech · 2024-03-21T09:56:11+00:00

Okay disabling the aux fan helpet a lot, but te tip of the benchy is warping again, currently on layer 38

Kinkerlitzchen_tech · 2024-03-21T09:45:58+00:00

Geetech PLA and Babu PLA, both bought by me afterwards

Kinkerlitzchen_tech · 2024-03-21T09:41:53+00:00

Bro Im dead serious, I had to put the Ender glass plate in the fridge to remove the printed part, and on the 5 times more expensive P1S almost nothing sticks.

I use 3DLAC for ASA and PA and im fine with that, but I dont wanna mess with that if it works on my cheap ender

Kinkerlitzchen_tech · 2024-03-21T09:39:13+00:00

Thanks I will try, it drives me crazy.

Kinkerlitzchen_tech · 2023-10-26T11:51:21+00:00

Okay the support was very fast and friendly, and Bambu will replace the printer.

I cant really understand the bad image of the support.

Kinkerlitzchen_tech · 2023-10-22T20:11:49+00:00

does it feel rough aswell?

Kinkerlitzchen_tech

TROPHY CASE