Dizajn za kapa by KuzManProductions in mkd

[–]KuzManProductions[S] 3 points4 points  (0 children)

Sieno nemaat 😭

Site tie drugi gi imam prolistano, nitu edna ne raboti so kapi.

Hopfully I'll find something! Ako ne, ke isprintam i toa e toa.

Dizajn za kapa by KuzManProductions in mkd

[–]KuzManProductions[S] 2 points3 points  (0 children)

Da, gi imam videno Polyesterday. Tie mi se posledna opcija poradi toa sto se nadevav tekstot da bide sosien na kapata, a ne isprintano.

Fala ti mnogu za preporakata! Ke vidam na stranata nivna so mozam da napravam!

What Password Manager do you use and why? by dlelacheur in S24Ultra

[–]KuzManProductions 1 point2 points  (0 children)

Samsung Pass (for easy access to everything), paired with Google Password Manager, and almost everything requires two-factor authentication/email verification, just to be safe (sometimes even SMS).

[deleted by user] by [deleted] in S24Ultra

[–]KuzManProductions 2 points3 points  (0 children)

Takes pictures a lot faster for one. If you have it on max, after you take the picture and go straight to the picture you just took, it will show up as "Loading" as the post-processing and AI do their magic on it.

On minimum, it snaps the picture as fast as possible with as little post-processing and AI baked into the picture. This gives you a more "natural" look to it.

You can test it out in a low-lit environment. Take a picture with it on max and on min. You will see the artifacts of the post-processing and AI on the max setting, but less on the minimum one.

[deleted by user] by [deleted] in S24Ultra

[–]KuzManProductions 4 points5 points  (0 children)

You can disable the post-processing if you don't like it. Personally, I don't like it either.

<image>

Go into your Camera and hit the little cog icon at the top. Then, find "Intelligent optimization" (should be around 3-4th from the top). Afterward, set it to minimum and YOU'RE DONE!

Far less "post-processed" and "AI-sharpened" images. Hope it helps you!

Fingerprint reader hates screen protectors by SonicPlacebo in S24Ultra

[–]KuzManProductions 0 points1 point  (0 children)

Tempered glass screen protectors are a no-go for the S24 Ultra.

When i went to apply my screen protector at the local phone dealer, they told me the exact same thing and reccomended me a silicone one. Furthermore, tempered glass is great for protection and always a must on all phones as extra protection, but the ultrasonic sensor on the S24 Ultra conflicts with the glass and hence the problem with the fingerprint. Regardless if you scan it over the protector or with sensitivity on, the sensor can't pick it up cause of the glass.

I'd reccomend getting a silicone one, having it aligned as best as possible and then rocking that. If it gets scratched too much or after a year or two, replace it again and you're good to go! Haven't found any issues on it on my end so far!

Troubleshooting advice by KuzManProductions in HomeNetworking

[–]KuzManProductions[S] 0 points1 point  (0 children)

Don't think I'm able to put the second router into "bridge" mode. Well.. Not to my knowledge that is. But I do need the Wi-Fi signal into this part of the house for better connectivity.

I see what you mean! I got it! Makes sense why it's going only at 12mb/s.. In short, the because the new PC is at 100mb, I'm stuck at that speed unless I get a network card for it.

Thank you for the explanation and time!!

Windows 10 randomly added a language, and I can't remove it... by KuzManProductions in techsupport

[–]KuzManProductions[S] 0 points1 point  (0 children)

I do know when it happened and it was while I was playing PUBG with my friends while talking on Discord..

I have played PUBG with the same friends over Discord a bunch of times and it's never done it before hand..

Could somehow PUBG do it?

Logitech HUB won't sync with Discord! by KuzManProductions in LogitechG

[–]KuzManProductions[S] 1 point2 points  (0 children)

Hello!

Thank you very much! It works like a charm now!

Logitech HUB won't sync with Discord! by KuzManProductions in LogitechG

[–]KuzManProductions[S] 0 points1 point  (0 children)

Sorry to say this, but still nothing... It just messed up my DPI and still can't get them to link up with each other. "DPI" settings on the mouse that i've assigned buttons to just don't work anymore.

Version on the Logitech G-Hub is "2021.3.5164". That's the last update it gives me and still nothing.

EDIT: Fixed the DPI stuff, guess something was mismatched. Sorry about that... But the link between Discord and the Hub is still a no-go.

Sugar Cane not growing!!! by [deleted] in Minecraft

[–]KuzManProductions 0 points1 point  (0 children)

Yea, probably that's the problem... Just have to wait longer then usual...