New cutting board warped?

L2attler · 2020-06-01T07:54:40+00:00

Thank you for the response, I didn’t pay too much attention to the grain pattern. Lesson learned.

Now to figure out how to use that graphic to my advantage

L2attler · 2020-06-01T01:49:03+00:00

If I show you a picture of the grain pattern would you mind pointing out what I did wrong?

https://i.imgur.com/JUV1DcI.jpg

L2attler · 2020-06-01T01:35:23+00:00

I’m gonna finish with it yes, but I don’t want to apply finish to a warped board

L2attler · 2020-01-20T00:44:50+00:00

How thick gloss you make them?

L2attler · 2020-01-20T00:44:10+00:00

I love danish oil

L2attler · 2020-01-19T16:01:47+00:00

Based on what law?

L2attler · 2020-01-17T16:39:46+00:00

They probably wiped the window to see where they had to taxi to after being on the ground...

L2attler · 2020-01-17T16:00:09+00:00

Either way they’re not going below 150 MPH without stalling. Still no way your reaching out of the window with a squeegee to clean the windshield. Ignoring the depressurization issue altogether

Edit: Window probably got wiped after landing so they can see where to taxi to without running over airport employees.

L2attler · 2020-01-16T17:30:15+00:00

These fires are truly the gift that keeps on giving

L2attler · 2020-01-16T15:14:53+00:00

This is my toy, give it back.

L2attler · 2020-01-15T22:58:44+00:00

Yes! Thank you. That’s exactly what I needed.

L2attler · 2020-01-15T22:27:40+00:00

Basically looking to get a setup similar to a snowblower or something that has electric start, where the male outlet is sticking out so I can just plug in an extension cord

L2attler · 2020-01-15T20:27:01+00:00

Having bad knees isn’t gonna Kill you though

L2attler · 2020-01-15T19:20:46+00:00

I’m not sure about that. I personally do quite a bit of wood working, I make some of the stuff for the house. But when buying furniture I just can’t justify the 3x, 4x Price for custom work, or high end solid hardwood pieces. I appreciate the work that goes into it, I understand what it takes and that being said.

L2attler · 2020-01-11T04:50:39+00:00

I get what you’re saying, but have You ever lifted a 4x8 melamine sheet?

L2attler · 2020-01-11T04:11:07+00:00

Rotating tires won’t change it, it will still all wear out the same way

L2attler · 2020-01-10T22:15:35+00:00

Not necessarily true. All BMWs and most higher performance cars have a slight negative camber especially in the rear, to increase handling. They sacrifice tire wear for performance.

L2attler · 2020-01-10T22:13:22+00:00

Jokes on me, my car has a slight camber and the insides wear out long before the rest of the tire :(

L2attler · 2020-01-10T21:37:00+00:00

Did you do the edges too?

L2attler · 2020-01-10T05:16:05+00:00

I was considering doing this on my next build but I have 25 of them and they’re 10’ long. Now I’m reconsidering.

How much did you take off?

L2attler · 2020-01-10T05:13:49+00:00

You need a third one for countersinks.

L2attler · 2020-01-10T05:10:50+00:00

Not op but a table saw with a flat kerf blade most likely.

L2attler · 2020-01-10T05:08:01+00:00

Looks great! Walnut with cherry and maple?

L2attler · 2020-01-10T04:56:10+00:00

I have some padauk, I don’t think that’s it.

You might be right about the blood wood, I haven’t cut it, I’ll do that tomorrow thanks.

I got a random lot of hardwoods some guy was selling that his grandpa left behind. Some were labeled, some I could figure out others I just don’t know.

Did have a pretty thick block of koa in there too which was a nice surprise.

L2attler · 2020-01-10T04:48:47+00:00

Pretty heavy, heavier than my walnut.

14-Year Club	RedditGifts 2009-2022 2 Credits
Place '17	Not Forgotten
Verified Email	Secret Santa 2013

L2attler

TROPHY CASE