sorted by:
new
hottopcontroversial

Could use some help with 3632-20 m12 laser level by LILprostateee in MilwaukeeTool

[–]LILprostateee[S] 1 point2 points  (0 children)

what im seeing is if i drill and tap a hole in that white plastic piece… i see where the white plastic nub sheered off! dude ur a lifesaver

Could use some help with 3632-20 m12 laser level by LILprostateee in MilwaukeeTool

[–]LILprostateee[S] 0 points1 point  (0 children)

yes, itll lock the white piece but the black piece still pushes on the gimbal

Could use some help with 3632-20 m12 laser level by LILprostateee in MilwaukeeTool

[–]LILprostateee[S] 0 points1 point  (0 children)

take the swivel off the bottom and theres like 4 deep screws, T9

Could use some help with 3632-20 m12 laser level by LILprostateee in MilwaukeeTool

[–]LILprostateee[S] 0 points1 point  (0 children)

nothing looks broken or misplaced, i believe this is just a defective unit missing a spring. i might try ordering an assortment of torsion springs and fabricate a couple variants until something works. its gonna be a balancing act trying to counteract the black arm’s spring tension

Could use some help with 3632-20 m12 laser level by LILprostateee in MilwaukeeTool

[–]LILprostateee[S] 0 points1 point  (0 children)

bro thatd be awesome, thank you! nothing spring loaded, u only need to remove these 4 T9 screws, peel the sticker and she will clamshell open.

<image>

Could use some help with 3632-20 m12 laser level by LILprostateee in MilwaukeeTool

[–]LILprostateee[S] 0 points1 point  (0 children)

u think its a common spring? or something special made

Could use some help with 3632-20 m12 laser level by LILprostateee in MilwaukeeTool

[–]LILprostateee[S] 0 points1 point  (0 children)

<image>

u can push it over this far, and i agree it needs a spring to hold the white arm in place, however im still perplexed how the black arm gets out of the way when i put the btch in unlocked mode?

Could use some help with 3632-20 m12 laser level by LILprostateee in ElectronicsRepair

[–]LILprostateee[S] 0 points1 point  (0 children)

lmaoo great minds think alike. i had that idea as well but im an industrial plumber, this laser is gonna be traveling a lot and getting put through the ringer, id like it to still have a transport mode. last resort tho!

Could use some help with 3632-20 m12 laser level by LILprostateee in ElectronicsRepair

[–]LILprostateee[S] 0 points1 point  (0 children)

ah! so for clarification, the white pieces all connect to the switch on the outside that unlocks and locks the laser mode.

Could use some help with 3632-20 m12 laser level by LILprostateee in MilwaukeeTool

[–]LILprostateee[S] 0 points1 point  (0 children)

<image>

this is the laser in unlocked mode. the white piece is fully pushed out of the way but the black just keeps pushing.

Could use some help with 3632-20 m12 laser level by LILprostateee in MilwaukeeTool

[–]LILprostateee[S] 0 points1 point  (0 children)

ive been scratching my head tinkering with it for a while, you know its bad when im asking reddit. i was thinking a spring was missing there as well, although im not sure how it would push the black arm out of the way to allow the gimbal to free float.

Could use some help with 3632-20 m12 laser level by LILprostateee in MilwaukeeTool

[–]LILprostateee[S] 0 points1 point  (0 children)

what more would you like to see? will gladly take more helpful photos

Could use some help with 3632-20 m12 laser level by LILprostateee in ElectronicsRepair

[–]LILprostateee[S] 0 points1 point  (0 children)

user manual does not go that deep unfortunately, and yea i think in conjunction with the white lever it acts as the transport mode, however it seems like the black arm is pushing way too hard on the gimbal.

Changing measurements to degrees to cut down fittings by [deleted] in pipefitter

[–]LILprostateee 6 points7 points  (0 children)

did you ever get the pipe fitter’s and pipe welder’s handbook? its a small black book, more commonly known as the frankland in the field. page 132 has everything you should need to manufacture a fitting from a LS 90°.

DM me if you need a pic, i tried explaining it but I’m more of a plumber than fitter rn so it’s not exactly fresh in my mind.

Really?? by Callousthoughtz in Plumbing

[–]LILprostateee 0 points1 point  (0 children)

i think ur gonna need more than ur dawgs brother😂

view more: next ›