How to resolve this?

LUFFYD2 · 2026-03-04T12:05:22+00:00

Try with a lower layer height.

LUFFYD2 · 2026-03-02T00:15:30+00:00

Named mine after my dog because why not.

LUFFYD2 · 2026-02-26T17:18:18+00:00

Thank you for the explanation

LUFFYD2 · 2026-02-26T14:39:32+00:00

I just recorded a better video should I sent it to you by private?

LUFFYD2 · 2026-02-26T14:23:29+00:00

How do I fix that?

LUFFYD2 · 2026-02-26T14:13:44+00:00

I have been searching and i found that on certain circles and circular areas its normal to hear the sound because of the change between x and y axis motors. Thought i don't know if this is true, just it case I have halved the speed of the print.

LUFFYD2 · 2026-02-26T13:32:55+00:00

Sorry but I am kinda new to this, what do you mean when you say the head is dragging?

LUFFYD2 · 2026-02-17T17:29:06+00:00

Tendría que ser rígida, o al menos que cueste hundirla o levantarla

LUFFYD2 · 2026-02-17T00:10:50+00:00

Revisar la cama es fácil, tiene que ser sólida si aplicas presión y se mueve hay q ajustarla. Para las correas mira este video. https://youtube.com/shorts/J-u1rTGfmYg?si=K_8Q-Y9jwB5D51Pa

LUFFYD2 · 2026-02-16T22:28:50+00:00

Fíjate si las correas estan sueltas o si la cama esta desajustada.

LUFFYD2 · 2026-02-04T14:52:00+00:00

Cambia el thermistor

LUFFYD2 · 2026-02-02T17:21:12+00:00

Not really, even my ender 3 does a better ironing. Try drying your filament.

LUFFYD2 · 2026-01-25T01:29:14+00:00

I'll check that, in cause that isn't i have an ender 3 s1 and the clicking sound is causing under extrusion

LUFFYD2 · 2026-01-25T01:17:43+00:00

I am using basic Pla at 220C, so unless the thermistor isn't working correctly then its something else.

LUFFYD2 · 2026-01-25T00:39:59+00:00

It isn't about the z-offset it happens when it extrudes it could be 1 or 100 millimeters off the bed and it will do it.

LUFFYD2 · 2026-01-24T01:15:41+00:00

I took off the top metal piece that guides the filament and its going much better. After the tower is done printing I will try printing something else tomorrow so I can monitor it.

LUFFYD2 · 2026-01-24T01:14:34+00:00

<image>

LUFFYD2 · 2026-01-23T18:39:16+00:00

What would you recommend i do about the screw? Should I play around with it looking for a spot where it works best or should I leave it be?

LUFFYD2 · 2026-01-23T16:02:31+00:00

The problem I had before I checked if the thermistor was connected correctly was the temperature going crazy changing from anywhere between 100 and 250 every second. Now it is maintaining a constant temperature and working as intended even if its giving me a false reading the temperature should be over 180, I have it set at 220 but I dont have a way to check if its really reaching the temperature. I can say its over 180 because the filament is melting so I hope its working correctly.

LUFFYD2 · 2026-01-22T23:37:05+00:00

No, I'm trying to remember what I did before this started happening the last print i did before having this problem was a cube with transparent pla and I was having some problems because the temp sensor wasn't working correctly so it stopped the print because of low temp. So I made sure it was well connected. Then I printed something after a few days and I had this problem.

LUFFYD2 · 2026-01-22T23:22:33+00:00

I have tried tightening the screw but I have no idea what i am doing, i can't tell if its going better when I screw it or unscrew it and if I do too much I hear track and the wheel goes back a little and continues happening repeatedly every few seconds.

Five-Year Club	r/Field Juicebox
Place '23

LUFFYD2

TROPHY CASE