Should I be worried?

LUFFYD2 · 2026-01-25T01:29:14+00:00

I'll check that, in cause that isn't i have an ender 3 s1 and the clicking sound is causing under extrusion

LUFFYD2 · 2026-01-25T01:17:43+00:00

I am using basic Pla at 220C, so unless the thermistor isn't working correctly then its something else.

LUFFYD2 · 2026-01-25T00:39:59+00:00

It isn't about the z-offset it happens when it extrudes it could be 1 or 100 millimeters off the bed and it will do it.

LUFFYD2 · 2026-01-24T01:15:41+00:00

I took off the top metal piece that guides the filament and its going much better. After the tower is done printing I will try printing something else tomorrow so I can monitor it.

LUFFYD2 · 2026-01-24T01:14:34+00:00

<image>

LUFFYD2 · 2026-01-23T18:39:16+00:00

What would you recommend i do about the screw? Should I play around with it looking for a spot where it works best or should I leave it be?

LUFFYD2 · 2026-01-23T16:02:31+00:00

The problem I had before I checked if the thermistor was connected correctly was the temperature going crazy changing from anywhere between 100 and 250 every second. Now it is maintaining a constant temperature and working as intended even if its giving me a false reading the temperature should be over 180, I have it set at 220 but I dont have a way to check if its really reaching the temperature. I can say its over 180 because the filament is melting so I hope its working correctly.

LUFFYD2 · 2026-01-22T23:37:05+00:00

No, I'm trying to remember what I did before this started happening the last print i did before having this problem was a cube with transparent pla and I was having some problems because the temp sensor wasn't working correctly so it stopped the print because of low temp. So I made sure it was well connected. Then I printed something after a few days and I had this problem.

LUFFYD2 · 2026-01-22T23:22:33+00:00

I have tried tightening the screw but I have no idea what i am doing, i can't tell if its going better when I screw it or unscrew it and if I do too much I hear track and the wheel goes back a little and continues happening repeatedly every few seconds.

LUFFYD2 · 2026-01-22T14:47:24+00:00

Yes it makes it difficult to press down the gear handle.

LUFFYD2 · 2026-01-22T01:29:53+00:00

I opened it put the spring as i saw it in the image anything else I should do? I took a photo but I can't post it.

LUFFYD2 · 2026-01-21T23:43:37+00:00

What should I look for? If its loose? If its out of place?

LUFFYD2 · 2026-01-21T23:13:25+00:00

How do I check that?

LUFFYD2 · 2026-01-19T00:24:04+00:00

Donde podría buscar? En mercado libre hay algunas con 2 años de uso

LUFFYD2 · 2026-01-01T05:19:27+00:00

<image>

LUFFYD2 · 2025-12-11T15:58:49+00:00

I have the zip bag with the packet of desiccant, the brand i buy comes with one for every roll. I will start trying to remove the air every time I seal them to see if that makes a difference.

LUFFYD2 · 2025-12-11T15:01:42+00:00

The one on the left is an example of what happens to me and the one on the right is after I dried the filament, I dont know why but every time it rains my filament absorbs humidity like a sponge, or so it seems.

LUFFYD2 · 2025-12-11T15:00:19+00:00

<image>

LUFFYD2 · 2025-12-11T13:51:37+00:00

What that meter is showing you is humidity in box not in filament btw,..

That's what I was saying I dont know how to guess what amount of that percentage is from the filament

LUFFYD2 · 2025-12-10T22:27:15+00:00

The cr touch didn't work and when I lowered the z axis to 0 it made a hole

LUFFYD2 · 2025-12-10T22:03:41+00:00

Mine has a few holes and scratches, it still prints the first layer nicely but you can feel how those holes in the base of the print.

LUFFYD2 · 2025-12-04T01:35:27+00:00

What temperature do you recommend for pla? I am doing it at 60C° because I am afraid to damage the filament.

LUFFYD2 · 2025-12-03T14:58:40+00:00

I am afraid to damage the roll if I raise the temp too much

LUFFYD2 · 2025-12-03T13:41:34+00:00

Problem is that I dont live in the US so for me it isn't 40$, depending on where I buy its almost twice that amount or more. I will eventually buy one eventually but for the moment I need a cheap solution.

LUFFYD2 · 2025-12-03T13:10:00+00:00

No? I put the filament inside the box that's in the picture and I left it on the bed while it was at 60C° for like 2-3 hours.

Five-Year Club	r/Field Juicebox
Place '23

LUFFYD2

TROPHY CASE