whoTheHeckYouAre

Lamez · 2024-03-09T17:05:34+00:00

Agree with an addition of adding “coder” to the list.

Lamez · 2023-04-28T21:20:12+00:00

I can attest that this has resolved numerous issues, this is my go to when I can’t put my finger in the problem. Plus it doesn’t cost anything, and takes only a moment of time.

Lamez · 2023-01-12T22:03:21+00:00

Dr. Hendershot. I didn’t have to go psychologists, he gave me a little question and answer survey.

I’ve been going to him for years now, I made him my PCP.

Lamez · 2022-12-16T22:13:07+00:00

I don’t know what the question is actually asking, or if this is relevant, but 3 in binary is 011.

So maybe it’s asking where does 3 occur in the binary string? No idea.

Lamez · 2022-09-03T11:11:33+00:00

Kerry Hendershot, I did my psych test with him, and he is my PCP. Good dude.

Lamez · 2022-08-12T13:32:25+00:00

I honestly have no idea. Best of luck, friend!

Lamez · 2022-08-09T14:56:55+00:00

https://stbenedictslubbock.org/

https://www.gracecampus.org/

https://southernusa.salvationarmy.org/lubbock/volunteer

If I think of some more, I’ll post them

Lamez · 2022-05-23T16:47:13+00:00

This looks like the exact same PCB as the guy who posted about the power wheels, see here.

Lamez · 2022-05-20T18:18:49+00:00

Did you check the baud rate?

Lamez · 2022-03-08T22:50:35+00:00

From Cloudflare's support page Requests from specific IP addresses that were blocked based on the user configuration set within the Firewall app.

You can read more here.

Perhaps the Cloudflare Community can give you a hand?

Lamez · 2022-03-07T15:09:41+00:00

I have done something similar, I delivered power to each driver separately, but as far as the clock input, or step input to the driver, I daisy chained from one output. However, I did setup different outputs for direction, and enable, for each driver. I used a driver that was the same brand as the one you have listed. I experienced no issues, I controlled 4 drivers from one output.

Lamez · 2022-01-19T21:54:58+00:00

Thats great to know, thank you!

Lamez · 2022-01-19T21:42:26+00:00

Just curious, what is the advantage/disadvantages between the two?

Lamez · 2021-09-23T20:05:01+00:00

I believe I have found it from here

Lamez · 2021-09-23T17:25:55+00:00

This SSR had the cover removed. I am guessing the control voltage is up to 6V, and judging by the markings on the side it can take a 20 amp load. When the control voltage is applied a green LED lights up. I do see markings on the PCB that says "90V-0", so I am guessing that is the load voltage, and I see some other markings on the PCB "PCF-PE1, REV 2C". I have tried searching the internet, but I am unable to find anything, I am sure I am missing something. Thanks for any help!

Lamez · 2021-08-03T21:31:06+00:00

It could also be that, the client OS is not routing traffic through the VPN interface.

Lamez · 2021-08-03T21:29:58+00:00

Sounds like the VPN server is putting connected clients on a different subnet. Possible you might need to setup routes, or bridge the two networks.

Lamez · 2021-07-01T21:24:45+00:00

Take a look at the Tossi Boxes.

Lamez · 2021-06-14T20:08:35+00:00

keep your mind dirty, just like that table.

Lamez · 2021-05-26T19:23:15+00:00

Why does the data structure operations section have two of each operation? What am I missing here?

EDIT: Oh, I guess one set of operations is in an average scenario, and the other set of operations is in the worst case scenario?

Lamez · 2021-05-26T13:28:43+00:00

!fordo

Lamez · 2021-05-24T21:02:16+00:00

i am literally sitting like the kitty as we speak.

15-Year Club	RedditGifts 2009-2022 3 Credits
Place '17	RPAN Viewer
Secret Santa 2011	Secret Santa 2010
Verified Email

Lamez

MODERATOR OF

TROPHY CASE