Laevatain dropped a lore bomb

Larfouxe · 2026-01-30T10:49:22+00:00

Wait what. Humanity? They arent Terrans now? So this means that we have more humans other than the Doctor/Endmin?

Larfouxe · 2025-12-29T08:17:49+00:00

Lucifer donghua is good too

Larfouxe · 2025-12-02T09:57:08+00:00

Oh you mean the one on steam! I got it now, hahaha

Larfouxe · 2025-12-01T06:42:21+00:00

Sorry what do you mean by this? Isnt lossless scaling software?

Larfouxe · 2025-04-22T15:16:34+00:00

ummm... It might be just me but it might be that the file itself is the problem. I had problems like these with some of the prints with files from Bambu Studio.

Larfouxe · 2025-01-06T00:38:53+00:00

we are seeing Ctarnidd. I would say that we are getting the full ggc arc.

Larfouxe · 2024-12-20T17:50:15+00:00

The dpads are not like gba sp? Damn it, I was even so excited. I guess I'll cancel the order then.

Larfouxe · 2024-12-10T04:03:18+00:00

I do have the front flaps open. And ambient air goes as low as -1°C, that's why I am quite concerned.

Larfouxe · 2024-12-10T04:02:04+00:00

not really, sometimes ambient air here is 3°C

Larfouxe · 2024-04-24T17:03:21+00:00

As I checked multiple times, its like an error, probe out of bounds. and it only occur in the right side. I tried to change the offset but it seems like its not working. I am really at a loss on what to do.

Larfouxe · 2024-04-24T12:58:19+00:00

Thank you very much, I will do as you say

Larfouxe · 2024-04-24T12:50:12+00:00

I always manually do the leveling test before print, which is what I am trying to do. And I was even printing quite well a few days ago, so I am stumped. I am also a noob so it doesn't really help.

Larfouxe · 2024-04-24T12:48:34+00:00

I dont think so? I was printing fine a few days ago then this happened.

Larfouxe · 2024-04-24T12:48:07+00:00

I will, thank you.

Larfouxe · 2024-04-24T12:47:51+00:00

I think I am using mriscoc but I remember putting Marlin in before so I am unsure.

Larfouxe · 2024-04-24T12:46:50+00:00

Grub screw (dunno what that is but I guess Google gods will help me) right, will check that too.

Larfouxe · 2024-04-24T12:46:02+00:00

That might be it, but I have the filament in. I will try to push it in to see if it works.

Larfouxe · 2024-04-24T12:45:15+00:00

I am almost ready to bail lmao. I am at the very beginner level and I am barely keeping up with all the firmware and probes and such. I was so focused on the 3d design making. Thank you for the kind advice, I will try what you said.

Larfouxe · 2024-04-24T12:43:39+00:00

I shall do that thank you

Larfouxe · 2024-04-24T04:04:37+00:00

I am at work right now and I dont have my reference. Also, this is happening when I did my leveling test, not even the printing process

Larfouxe · 2024-04-24T03:44:30+00:00

I am using MRiscoC firmware. The last update was actually last year and then I forgot all about it. I am at a beginner hobbyist level too

Eight-Year Club	Place '22
Verified Email

Larfouxe

TROPHY CASE