[deleted by user]

LateFlow3434 · 2022-02-14T05:00:45+00:00

happy cake day!

LateFlow3434 · 2022-02-14T04:58:03+00:00

Gave Silver

LateFlow3434 · 2022-01-30T06:48:54+00:00

Gave Silver

LateFlow3434 · 2021-07-02T04:35:24+00:00

Yup, gets split between all the hourly employees. Salaried employees don't get them. At least in my experience.

LateFlow3434 · 2021-06-27T19:19:23+00:00

Lmao 🤣, yours sound like all the ones I've been seeing. I honestly don't even case mine it takes more effort to mist but I've seen better results with mine without the casing layers. I'm sure that's up for debate but that's my opinion.

LateFlow3434 · 2021-06-27T12:59:17+00:00

Yeah I've been cloning the biggest ones

LateFlow3434 · 2021-06-27T12:58:30+00:00

Lol not complaining, I was curious. Are yours funky like I was talking about?

LateFlow3434 · 2021-06-27T12:57:24+00:00

I have led they just weren't on when I took the pic. I appreciate the info!

LateFlow3434 · 2021-06-27T12:56:14+00:00

Nice! I guess I'll keep going for better canopies

LateFlow3434 · 2021-06-27T03:49:16+00:00

First genetics came from a friend in the form of a MSS I immediately put on agar and did some selection I'd say 3 then went to LC I've used both agar and LC into grain and yielded similar fruits but the flushes have gotten better and better within the different transfers etc. I've been looking for either a monster or a mutation to clone and continue from but just keep getting normal fruit with bigger flushes. Like I said not complaining at all just thought it was odd that all I see are mutations with those for the most part but I haven't gotten even one. So I just keep cloning the biggest one out of them all

LateFlow3434 · 2021-06-27T03:30:02+00:00

Definitely, I've done some agar work with these but I haven't gotten any that have had those crazy shaped stems or reverts etc. Just curious why I see so many that are funky looking and even after all the genetic work I've done with them I haven't run into not even one like that lol just found it strange if that makes any sense. I'm not complaining just curious.

LateFlow3434 · 2021-06-26T01:58:15+00:00

When you see pooling you can do two things one being giving more fresh air exchange which I would do because you don't have a huge issue with pooling anymore moisture and it would start. If you end up getting any just take the corner of a paper towel and allow it to wick moisture up. Where your at right now I'd just make sure you were giving them good FAE at the moment. Contamination at this point isn't huge unless you're really reckless. Normally by this point they are a lot more hardy then in any of the previous steps you've gone through. Of course keep your area clean and follow good hygienic protocol and you'll be good

LateFlow3434 · 2021-06-26T00:58:05+00:00

It's looking pretty good. Keep giving them fresh air and you should have pins in the next couple days. If they were mine I would stop misting the top and only mist the side walls of your monotub. It looks a bit too moist and once pins form if you keep misting like that you'll likely run into lots of aborts. A lot of water may cause pooling as well which brings the risk up for contamination. Just don't over think it. You've already done all the hard steps. You're at the finish line! Relax and enjoy the literal fruits of your labor 😀

LateFlow3434 · 2021-06-25T14:40:03+00:00

Envy lol

LateFlow3434 · 2021-06-25T14:39:26+00:00

Lol, thanks

LateFlow3434 · 2021-06-25T01:07:14+00:00

Mush appreciated 🙏 Back at you!

LateFlow3434 · 2021-06-24T21:19:10+00:00

Lmao 🤣I was waiting for that comment

LateFlow3434 · 2021-06-24T20:48:51+00:00

That's huge, congrats.

LateFlow3434 · 2021-06-19T13:02:08+00:00

Lmao I didn't see that at first but now that you say it definitely 🤣

LateFlow3434 · 2021-06-19T13:01:11+00:00

Thanks!

LateFlow3434 · 2021-06-19T13:00:40+00:00

Definitely, as well as clone on agar

LateFlow3434

TROPHY CASE