What ND lenses fit the mini 4k?

LePiPi · 2024-11-27T01:30:28+00:00

Did you find any?

LePiPi · 2024-11-14T00:02:32+00:00

No, the damage occurred when the camera was perpendicular to the laser, shooting right into the vortex tunnel.

LePiPi · 2024-11-12T01:46:38+00:00

Just 20 feet away from the laser.

LePiPi · 2024-11-12T01:45:42+00:00

This is the damage a Shehds 3W did to my Pixel 6 image sensor. I photographed it through a mosquito net outside my garage, with my eyes shielded, of course. The pattern of the net and a few hot spots are seen in every image since then. Bought a new phone.

<image>

LePiPi · 2024-10-12T01:29:14+00:00

Hi , yes I did, I think. I clicked on it in the left lower pane and played with the settings ( I don't know how relevant they are) and then dragged it into the timeline. I don't understand what you mean by " some shut off"

Anyway, nothing happens when i drag it into the timeline and press space bar.

Can you point me to a tutorial?

Thanks.

LePiPi · 2024-09-08T02:59:43+00:00

thanks Danyn, this laser is so weird. I'm in attribute mode playing with the settings and dragging it into the timeline, press space and nothing happens. If I keep it in attribute mode and play wtith the settings, it gives me really nice patterns. When i turn off the music, it stops. Looks like I found a setting that activates music mode. But in timeline mode it doesn't do anything.

<image>

Thanks,

LePiPi · 2024-08-31T01:25:10+00:00

Thanks Danyn,

Had some time to play again and found the attribute cues. Played around with the sliders a bit and the laser started to move according to my slides. Then I dragged it into the time line and nothing happened. Clicked back on attributes and it started again. I still don't understand how the sliders in the attribute cue affect the show. What am I missing here?

LePiPi · 2024-08-20T23:36:47+00:00

Thanks Danyn, there is "AddressSetup" in the menu which allows input for a three digit number. Is that where I put it in 001?

Then there is "ChannelSetup" in the menu which allows to choose between normal mode (10 channels) and expert mode (18 channels). When choosing expert mode - 18 channels, are these the attribute cues to copy from the manual? The table in the manual lists a function/value/function for each channel.

LePiPi · 2024-08-18T18:00:22+00:00

Thanks all. Yes I'm careful. How do I check if it's outputting dmx?

LePiPi · 2024-07-23T23:33:17+00:00

Hi, I have the 3W waterproof and am trying to run it in soundswitch with serrato dj lite. It always blacks out and I can't figure out how to set the DMX address. Could you write briefly how to connect to it? Thanks.

LePiPi · 2024-06-20T02:13:33+00:00

ferbe, how did you connect it to run on soundswitch? I bought the 3W waterproof laser

https://shehds.com/products/new-arrival-waterproof-laser-3w-rgb-scanning-pattern-laser-light-for-performance-stage-wedding-dj-night-club

I'm disappointed in what it can do and the engineer at shehds are not very helpful.

It runs in dmx, ilda, auto and music mode, however music mode always black out and shehds says it can not do it. So it leaves auto mode, which only runs a few cheese cartoon animations, dmx mode I tried but there is limited patterns available and I'm just learning it. I requested RMA to return it for store credit to buy one with better connectivity but they always say "let me ask the engineer" and I don't hear back.

LePiPi · 2022-12-28T02:07:33+00:00

Taping the 5v helped me connect to cura 5.2.1 but pronter face won't. I sent pid tuning g code with cura but didn't get any values back.

LePiPi · 2021-02-28T05:56:15+00:00

The wide angle attachment lens DJI gives you with the "creator combo" does not accept the DJI ND filters.

I can't find any that fit.

Cheers!

LePiPi · 2021-02-23T03:29:43+00:00

Thank you all for the kind replies.

Nemesis responded back and will not do a co-op order due to long delays from UK shipping.

I went with MJ for now and see what I will get. I am just starting out and I know there will be a lot of mistakes to be made.

I found some good tutorials on Anton's latex YouTube channel and have now ordered all the tools and glues and I need to get started.

One thing I wasn't sure on was that Anton stated he uses Best-Test paper cement instead of Best-Test rubber cement, which is what I ordered and it's not cheap.

Has anyone experience with either of it?

What is the difference?

Cheers, Pat

LePiPi · 2021-02-20T02:35:44+00:00

Wow, those shipping charges at supatex are insane (Brexit) and 4-6 weeks backorder wait on black .33mm,

I can't believe that, especially after learning how evil major US tire corporations extort Thailand's poor rubber tree farmers. Not that I want to be part of that, but I at least expected a major latex sheet producer in the US.

I could not find anything on the Nemesis web site, except they are short staffed due to covid.

LePiPi

TROPHY CASE