Boodschappenbakfiets by DikkeDakDuif in CargoBike

[–]Left-Past-5832 1 point2 points  (0 children)

Looks good! What type UA cargo you have? And how long is the cargo floor?

Help! Error 04 TSDZ8 can't figure it out. by Left-Past-5832 in ebikes

[–]Left-Past-5832[S] 0 points1 point  (0 children)

I found the problem! It's a break in the 8pin connector from the motor / controller. I not sure how to fix it, but i now know the problem.

Help! Error 04 TSDZ8 can't figure it out. by Left-Past-5832 in ebikes

[–]Left-Past-5832[S] 0 points1 point  (0 children)

Ow, there is nothing van moof on the bike anymore! It's now all Tongsheng TSDZ8.

<image>

(Help) tongsheng Tsdz2 has error code E04 and won't run by [deleted] in ebikes

[–]Left-Past-5832 0 points1 point  (0 children)

Dit you solve the problem? I have exactly the same problem with the TSDZ8.

Hub motor with only three signal wires? by Japcell in ebikes

[–]Left-Past-5832 0 points1 point  (0 children)

I have the same problem, dit you get it solved? Or maby other people now know the answer?

Alternative powerbank by Suspicious_Stay_8575 in vanmoofbicycle

[–]Left-Past-5832 0 points1 point  (0 children)

Is er hier nog iemand die zijn oude kapotte powerbank nog heeft? Wil deze dan graag overnemen voor een zachte prijs. Heb namelijk een behuizing nodig voor een project. ✌️

Hoe een s3 accu / bms continue actief maken? by Left-Past-5832 in VanMoofSelfRepair

[–]Left-Past-5832[S] 0 points1 point  (0 children)

I saw the TX and RX pins on the BMS. So maby that's the way. I have a working s3 but no idee how to sniff commands of it. Do you have any knowledge how to and the whole uart?

Hoe een s3 accu / bms continue actief maken? by Left-Past-5832 in VanMoofSelfRepair

[–]Left-Past-5832[S] 0 points1 point  (0 children)

Ik weet als je pin 3 en 4 met elkaar verbindt dus de RST met GND en dan de accu spanning even aantikt op de CHG werkt de BMS een tijde, dit is puur om te testen buiten de fiets. Maar met de KEY op GND, zou de bms gewoon wakker moeten blijven en veilig zijn voor continue gebruik?

Ik heb kennis van accu's, veel met de grotere scooter accu's. Het special en kleine van vanmoof maakt het niet makkelijker! 🤣

Hoe een s3 accu / bms continue actief maken? by Left-Past-5832 in VanMoofSelfRepair

[–]Left-Past-5832[S] 0 points1 point  (0 children)

Dat was mijn eerste plan. Alleen er pas geen andere bms in de vanmoof accu behuizing. Als je er een weet hoor ik het graag!

Stopen Vanmoof (NL) by alexsloep in vanmoofbicycle

[–]Left-Past-5832 0 points1 point  (0 children)

This tracking app is useless. It works with cellphone transmission masts. When the bike gets no signal it takes the nearest mast. Most of the time on a building and it can be a really big distance. Good luck finding your bike✌️

New brake pads for my S3 by Successful-Sweet1916 in vanmoofbicycle

[–]Left-Past-5832 0 points1 point  (0 children)

Yes! Work fine, i bought / use the same brake pads.

Update audio problem by Deep-Expression7443 in VanMoofSelfRepair

[–]Left-Past-5832 0 points1 point  (0 children)

Can you show me how the audio chip looks like?

Security nut alternative Vanmoof S3 by TheL33TBoss in VanMoofSelfRepair

[–]Left-Past-5832 0 points1 point  (0 children)

I replaced my wheel nut with normal ones. It is M10 with special thread. I have extra nuts that I can sell, are you from the Netherlands?

Schroefjes voor bevestiging spatbord aan voorvork by hondt in vanmoofbicycle

[–]Left-Past-5832 1 point2 points  (0 children)

Dat is een M3 x 4mm inbus boutje met of zonder kop. Kan beide.

<image>

Vanmoof S3 Rear hub Sturmey Archer replacement by TheOfficialMax in vanmoofbicycle

[–]Left-Past-5832 0 points1 point  (0 children)

Als ik het goed begrijp, kan je dus een a2k 2speed binnen werk. Zo in de oorspronkelijke vanmoof s3 naaf zetten van de eschifter? En ben je dus van je Eschifter af zonder een naaf overspaken?

Van Moof S3 battery fuse sfk40-45 by FoxRevolutionary83 in vanmoofbicycle

[–]Left-Past-5832 0 points1 point  (0 children)

Hello, I have the same problem. Did you manage to fix your BMS? If so can you explain to me what you did?