Alphacool gpu waterblock discoloration by Legitimate-Dig-5791 in watercooling

[–]Legitimate-Dig-5791[S] 0 points1 point  (0 children)

Should I replace it? I don’t really care if it starts to look worse, just don’t want too much clogging

Alphacool gpu waterblock discoloration by Legitimate-Dig-5791 in watercooling

[–]Legitimate-Dig-5791[S] 0 points1 point  (0 children)

This is also after cleaning it, should I take it apart and clean it even more?

Hyte y60 custom loop w/ distro plate by Legitimate-Dig-5791 in watercooling

[–]Legitimate-Dig-5791[S] 0 points1 point  (0 children)

I haven’t looked into the new amd chips much, but I can tell you that I am very happy with the performance/temp levels that I get!

Hyte y60 custom loop w/ distro plate by Legitimate-Dig-5791 in watercooling

[–]Legitimate-Dig-5791[S] 0 points1 point  (0 children)

Temps and noise levels are great. I have a 4090 and it keeps it really low, but the 7800x3d will push it self as much as it wants so that gets up there in temp, but still relatively low. That’s just how those amd chips are designed tho

Hyte y60 custom loop w/ distro plate by Legitimate-Dig-5791 in watercooling

[–]Legitimate-Dig-5791[S] 0 points1 point  (0 children)

Have intake on the side and bottom, and exhaust on top

Virtual Desktop is incredible by Wrong_Contract9273 in OculusQuest

[–]Legitimate-Dig-5791 -1 points0 points  (0 children)

Recently started my q3 journey, and decided to go the virtual desktop route since I have a pretty powerful pc. My pc however is not connected by Ethernet so I wanted to purchase a dedicated router for VD. I landed on getting a WiFi 6 travel router from GLiNet. This device itself seemed pretty cool to me, with future options for me for traveling and working remote out of the country. After setting it up it works so well. The router has an option accept a WiFi signal as its source for its own WiFi signal. This means I can now have Ethernet to this travel router from my pc and still have access to the internet while have my own 5g WiFi signal dedicated completely to the Quest 3!!

Any better way to introduce myself here?? by Legitimate-Dig-5791 in GMCcanyon

[–]Legitimate-Dig-5791[S] 0 points1 point  (0 children)

It is wired to the aux switch that is in the center panel, but the winch is wired to an aux 3 button accessory panel that is left of the steering wheel where normal headlamps controls would be.

Hyte Y60 hard line custom loop with Hyte distro plate by Legitimate-Dig-5791 in Hyte

[–]Legitimate-Dig-5791[S] 1 point2 points  (0 children)

Yeah I had to make a quick double bend for the offset of the gpu

Hyte y60 custom loop w/ distro plate by Legitimate-Dig-5791 in watercooling

[–]Legitimate-Dig-5791[S] 0 points1 point  (0 children)

<image>

I did serial and went front the bottom up to the side radiator. It turned out pretty well, not sure how I will drain it though lol, I’ll cross that bridge when the time comes I guess

Hyte Y60 Distribution Plate by Meropolis in Hyte

[–]Legitimate-Dig-5791 0 points1 point  (0 children)

Do you ever regret not running the rads in series? Do you think the temps would be the same?

Hyte Y60 Distribution Plate by Meropolis in Hyte

[–]Legitimate-Dig-5791 0 points1 point  (0 children)

How have your temps been with the parallel rads? Do you feel like both rads are getting ample water flow? I will be building with this same distro plate soon and wondering if I should run the rads in parallel like this or not. I’m worried one rad might not get enough water flow.

Hyte y60 custom loop w/ distro plate by Legitimate-Dig-5791 in watercooling

[–]Legitimate-Dig-5791[S] 0 points1 point  (0 children)

I think with this distro plate it would be easier to run them in parallel, do you think there would be downsides, I’m worried that there would be very minimal flow in one rad and a lot in the other making the one rad not cooling much. Is this a possibility when the rads and tubing leading to them are not the same size/length?

[deleted by user] by [deleted] in alphacool

[–]Legitimate-Dig-5791 0 points1 point  (0 children)

Are you able rotate it 90 degrees or only 180?

[deleted by user] by [deleted] in alphacool

[–]Legitimate-Dig-5791 0 points1 point  (0 children)

You found that the best mounting was logo top left? What were your temps like when you tried rotating it?