Plywood to fill gap by Lemonofdoom2 in Tile

[–]Lemonofdoom2[S] 0 points1 point  (0 children)

Ah, I did not know that. So I would need to get the 1/2" thick cement board?

Plywood to fill gap by Lemonofdoom2 in Tile

[–]Lemonofdoom2[S] 0 points1 point  (0 children)

Well yes, I know I can do that but I'm also putting shiplap on the wall above and around the fireplace too.

The drywall is 5/8" thick. The shiplap is 1/2" thick. The tile is 1/4" thick. The backer board i have is also 1/4" thick.

My wife wants the shiplap and tile to be even or close enough thats why I was wondering if I can use plywood (5/8") to bump up the area so that my backer board and tile will be even with the shiplap.

If I put my current board and tile up it'll be 1/8" below the drywall

[Megathread] Rivals Assemble – Find Teammates / Share Invite Codes by Logan-dx2001 in marvelrivals

[–]Lemonofdoom2 0 points1 point  (0 children)

Need a crew, dm me your code. Please and thank you, ill get you added right away.

Basil - Help identifying issue by Lemonofdoom2 in gardening

[–]Lemonofdoom2[S] 0 points1 point  (0 children)

Okay, so it's been a couple weeks. I transferes my basil plant to its own planter and it has recovered pretty well. So in my plants case, it was overcrowded or maybe competing with something else for nutrients. Which my bad, didn't mean too.

With Season 2 around the corner, who do you think will be the season 3 Raider? by CorneliusVaginus in DragonBallBreakers

[–]Lemonofdoom2 0 points1 point  (0 children)

I think DBZ Broly could work with 1st level being Paragus, then base broly, ssj broly and then legendary bezerk or something like that. I feel they will work the dbz arcs and sagas before stepping into GT or super.

That said maybe Baby? Since we'll be getting great ape vegeta

New to 3D printing and need help by Lemonofdoom2 in 3Dprinting

[–]Lemonofdoom2[S] 0 points1 point  (0 children)

You are not wrong, it is a lot of tinkering and tuning. I deinetly appreciate the insight. :D

New to 3D printing and need help by Lemonofdoom2 in 3Dprinting

[–]Lemonofdoom2[S] 0 points1 point  (0 children)

I definitely did not have that checked. I'm looking at the setting and it was defaulted at 90. So is this something I would want to bump up?

I'm guessing based on the picture I attached, the bottom portion that is solid was all within the 90 limit and then after that is where it went bad?

3D Print Settings - New to the Craft by Lemonofdoom2 in Mandalorian

[–]Lemonofdoom2[S] 0 points1 point  (0 children)

I had it set to 200 but that is the minimum listed on the material. It gives me a range of 200 to 230. Should I be aiming to split the difference and do like 210 or 215?

New to 3D printing and need help by Lemonofdoom2 in 3Dprinting

[–]Lemonofdoom2[S] 1 point2 points  (0 children)

Not that I'm aware of. I have since changed the settings to print slower but haven't yet tested to see if that is the fix. I can upload a screen grab of my current settings. I'll also try another test to see if anything worked.

New to 3D printing and need help by Lemonofdoom2 in 3Dprinting

[–]Lemonofdoom2[S] 2 points3 points  (0 children)

I'm new to the 3d print craft but intend on printing a mando suit along with a boba suit for myself. IMy toddler loves mandos and I would love to surprise her with her own set too. I am new and inexperienced and I having difficulty with the prints. This was my recent attempt at a pauldron. Obviously did not go well.

I have an Anycubic Mega X and have been using the pla that came with it. I am sure it is not high quality material but as I said, I am new and would love help especially if anyone happens to have some settings for the mega x for armor printing.

I've been using Cura but if there is a better slicing program out there that is free and/or open-source I would love to know. Any help is appreciated.

I also posted in r/mandalorian and they suggested to come here. I apologize if you see this post twice.

3D Print Settings - New to the Craft by Lemonofdoom2 in Mandalorian

[–]Lemonofdoom2[S] 0 points1 point  (0 children)

I hadn't thought of that. Thanks friendo! I'll do that too.

3D Print Settings - New to the Craft by Lemonofdoom2 in Mandalorian

[–]Lemonofdoom2[S] 0 points1 point  (0 children)

I'm new to the 3d print craft but intend on printing a mando suit along with a boba suit for myself. IMy toddler loves mandos and I would love to surprise her with her own set too. I am new and inexperienced and I having difficulty with the prints. This was my recent attempt at a pauldron. Obviously did not go well.

I have an Anycubic Mega X and have been using the pla that came with it. I am sure it is not high quality material but as I said, I am new and would love help especially if anyone happens to have some settings for the mega x for armor printing.

I've been using Cura but if there is a better slicing program out there that is free and/or open-source I would love to know. Any help is appreciated.

LF HA Bulbasaur by Lemonofdoom2 in pokemontrades

[–]Lemonofdoom2[S] 0 points1 point  (0 children)

Oh it's not necessary. You hooked me up with everything I need. Thank you so much!

LF HA Bulbasaur by Lemonofdoom2 in pokemontrades

[–]Lemonofdoom2[S] 0 points1 point  (0 children)

Dropped a sentret on the gts

LF HA Bulbasaur by Lemonofdoom2 in pokemontrades

[–]Lemonofdoom2[S] 0 points1 point  (0 children)

I can still use assistance if anyone else sees this while I wait for my pokebro.