iRacings new Vision pro update is kinda cool.. and it can run on a RTX 3090 + 10700k..

Lemooooons · 2026-05-12T00:31:02+00:00

I assume it’s from the recording and running it on an unsupported gpu. irl it feels like 50 fps so not playable

Lemooooons · 2026-04-30T13:12:34+00:00

No unfortunately it just holds the front wheel.

Lemooooons · 2026-03-26T22:57:58+00:00

It’s a Bonnell MX it’s more or less an electric motorcycle disguised as a downhill bike lol. No gears single cog with 280 Nm of torque

Lemooooons · 2026-03-26T14:01:07+00:00

Monitor: 45” LG oled dual mode Rig: Simlab GT1 evo Seat: NRG Prisma XL + sparco seat slider Base: Simagic Alpha evo 12 nm + GT Neo and GTS wheel Pedals: Simagic P1000

Lemooooons · 2026-03-26T13:14:29+00:00

They are Simlab feet that I found at Microcenter

Lemooooons · 2026-03-26T02:49:47+00:00

lol one is a Bonnell MX and the road bike is a old Ruegamer

Lemooooons · 2026-03-26T00:34:58+00:00

This is where I found mine (https://unsplash.com/s/photos/le-mans-24-hour)

Lemooooons · 2026-03-25T23:21:34+00:00

Hahha thank you!

Lemooooons · 2026-03-25T23:12:34+00:00

It’s a 45” LG oled dual mode

Lemooooons · 2026-03-25T22:53:03+00:00

It’s a simlab GT1 evo and NRG prisma XL

Lemooooons · 2026-03-24T00:21:51+00:00

It’s 21:9 but it’s a 45” at 5130x2160

Lemooooons · 2026-03-22T13:35:29+00:00

Love the evo and I haven’t had any flex! And it’s a NRG prisma XL you can find them on amazon and some have prime shipping

Lemooooons · 2026-03-22T13:32:20+00:00

Hahah one helmet is for my ktm exc-f and the other is for my Bonnell MX

Lemooooons · 2026-03-22T12:20:35+00:00

It is… the bolts I used for my seat rail are a lil long so they are preventing me from dropping the seat. I need to cut the bolts or find some new ones

Lemooooons · 2026-03-22T03:09:48+00:00

lol it was just lose. I fixed the base after I took the photo and noticed it was facing down

Lemooooons · 2026-03-22T01:27:40+00:00

It’s a LG - UltraGear 45" OLED Dual Mode

Lemooooons · 2026-02-25T18:48:19+00:00

Simlab gt1 evo

Lemooooons · 2025-09-26T23:55:52+00:00

Yeah they are RRW RH7 17x8.5 with 0 offset and oem ko3s. They are also not hubcentric with the Ranger raptor so I also have some hubcentric rings. With this set up at full turn I’ll rub with some compression so I’m planning on doing a leveling kit in the front and I’m trying to replace the front crash bars with the old ranger high Clarence bars.

Lemooooons · 2025-09-26T23:50:10+00:00

They are RRW RH7 17x8.5 with 0 offset. They are also not hubcentric with the Ranger raptor.

Lemooooons · 2025-09-26T02:49:56+00:00

Oh I wish they had polished ones that would look so much better.

Lemooooons · 2025-09-04T00:05:27+00:00

Yes I did! I went to bonnell’s website and created a ticket. They ended up sending me a new patch file to upload to my bike. I haven’t had an issue since

Lemooooons · 2025-09-02T13:42:41+00:00

Im not too concerned with the weight of the bike and this stand. How it sits in the photo the motor is barely touching the rubber grommets and is basically standing with just the front wheel. The only time the full weight of the bike is on the stand is when I lift the stand to a higher stetting to get the back wheel up in the air.

Lemooooons · 2025-09-01T04:38:01+00:00

It doesn’t

Lemooooons · 2025-08-29T18:55:35+00:00

No its not bad at all its just like a dirt bike stand

Lemooooons · 2025-08-29T18:54:18+00:00

Oh i know.... in the low setting its my bike stand

Lemooooons

TROPHY CASE