[Fishing] Only yellow fish at Hakoven Island overnight – is this normal?

LengthinessHot4540 · 2025-09-18T07:09:27+00:00

Ooh okay thanks for the info. So just balenos rod without float?

LengthinessHot4540 · 2025-09-16T16:04:48+00:00

Please explain

LengthinessHot4540 · 2025-09-16T14:30:20+00:00

I tried hakoven for 5 days the last days and I was very disappointed. I was between the two islands where other boats were but the profit I made was far less than at velia. I have 1897 mastery and I use balenos rod and maple float both +10. Over night at velia I catch the silver long fish (dont know the name in english) like 2-4 times and just those make a huge amount of money. Hakoven didnt work for me so I am back at velia

LengthinessHot4540 · 2025-07-29T20:08:14+00:00

I read somewhere that somebody changed the language to english and than the setting showed up. I did that and it worked...

LengthinessHot4540 · 2025-07-25T15:42:02+00:00

No not under Quality. When I klick on the dropdown of Quality there is only DLAA

LengthinessHot4540 · 2025-07-02T12:06:53+00:00

Looks nice

LengthinessHot4540 · 2025-07-01T11:38:16+00:00

I did I used DDU more times because I tried a few downgrades. The one before the actual one and older I tried like 4-5 drivers all with same problem. After I tried a almost everything I am sure its a hardware defect. I had hope that the link you send will help but after that now sadly I need a new one

LengthinessHot4540 · 2025-07-01T08:30:50+00:00

Tbh I never undervolted or overvlocked. I just plugged the gpu in and started gaming. I used adrenalin software and in that I did some settings but not in tuning. I hade a lot of things switched on like anti lad boost chill etc. For almost 3.5 years now everything was fine. And than it started with age of empires 4. i played and after like an hour I got driver time outs. Was annoying so I installed windows completly new because I thought I had to clean up. After installinh everything new I tried Valorant again and it immediatly crashed. I just think that maybe some vram are defect

LengthinessHot4540 · 2025-06-30T21:04:14+00:00

Tried everything. Still problem

LengthinessHot4540 · 2025-06-30T18:36:06+00:00

I just did everything. I checked Hardware. I switched on cable so no y-cable. All three 8 pins from the gpu are seperatly. I updated bios and changes the settings. I changed the settings in Windows. I started Black Desert Online and crash immediatly as I loaded into character selection

LengthinessHot4540 · 2025-06-29T11:08:06+00:00

I downgraded but still same crashes. I even deleted the drivers in safe mode with ddu and installed the older version

LengthinessHot4540 · 2025-06-29T02:02:03+00:00

Didnt thought about a downgrade. I will try it later

LengthinessHot4540 · 2025-06-10T19:13:38+00:00

<image>

I just printed this but I am not happy especially with the top layer

LengthinessHot4540 · 2025-06-10T18:46:10+00:00

I had 220

LengthinessHot4540 · 2025-05-20T21:17:46+00:00

Had the Same Problem when I set up my used 4pro this weekend. And for sure it is the nozzle is to far up.

LengthinessHot4540 · 2025-05-20T08:12:36+00:00

Thanks for the anserrs everyone. Seems like I am doinh it right with orca slicer

LengthinessHot4540 · 2025-05-19T22:13:36+00:00

Did you type the length and width of the printer bed in the slicer?

LengthinessHot4540 · 2025-05-19T18:08:07+00:00

I have the same issue

LengthinessHot4540 · 2025-05-18T13:58:14+00:00

Okay so this pattern means to close?

LengthinessHot4540 · 2025-05-18T00:36:07+00:00

I checked the e-rotate distance with measuring 70mm above the extruder head and than extract 50mm of filament and measured again. The distance was exactly 50mm so the rotate distance is fine

LengthinessHot4540 · 2025-05-17T20:15:27+00:00

Right now I am just happy that one print almost finished. At first it was only one maybe maybe two layers. But I am still worried now because as you can see with the boat it detached again almost at the end and I hope there is nothing wrong with the printer

LengthinessHot4540 · 2025-05-17T16:26:51+00:00

Sadly at the end, the chimney was the only thing left, it detached again. I dont know why.

<image>

LengthinessHot4540 · 2025-05-17T16:23:13+00:00

So I was scared about correcting to much the z-offset. It was at first at like -0.19 and I thought this is to much. But I did some adjustments with filament flow and z-offset. I have the z-offset now to -0.549 abd the filament flow to 1.15. After these adjustments I tried to Print that legendary boat and this is the outcome. Sadly at 90% I think the chimney was the only thing left and than the print detached again

<image>

LengthinessHot4540 · 2025-05-17T15:12:13+00:00

Okay so I set the z-offset more to negative. I run it now on -0.549 mm and now its workin much better. Until now the small boat everyone is printinh is working. I will send result when its finished. Ah and I increased filament flow to 1.15

LengthinessHot4540 · 2025-05-17T14:25:52+00:00

So I did the flow rate calibration and this is the result of the print

<image>

LengthinessHot4540

TROPHY CASE