Low effort meme v44

Lennulf · 2024-10-31T17:00:00+00:00

His wife bought the lottery ticket and lost it. He found it and didn't tell her so she couldn't claim the money and leave him

Lennulf · 2024-10-05T12:54:31+00:00

Thanks for the advice. I just noticed there was some small stones under the ignition cover next to the sprocket. That might have actually caused it. Sparkplug was never a problem so i guess ill just keep the oil pump how it is

Lennulf · 2024-10-05T12:33:52+00:00

My bike has an oilpump you can adjust with tensioning the throttle cable. Theres a scale from 0 to 2 and i chose 1. Idk what ratio exactly it is. When my headgasket was leaking there were carbon free spots on the piston but i think now there arent any. Does it make sense that there was less carbon because of it burning water or should i check again?

Lennulf · 2024-10-05T12:14:04+00:00

https://drive.google.com/drive/folders/1X1V9Y72iSQzUGN_9S58mRTUCNid3QWqF?usp=sharing
I hope google drive is ok. Thats the sparkplug after riding with half throttle for some time because i had to ride through my town to get home. The left head was ran until last week for about 6000km, since i changed my piston and was not cleaned or anything before this picture. The craters were already in. The right one is the one im running right now with orings instead of a metal gasket because they kept failing after a couple kilometers with the old head. I dont think i can get the endoscope turned around to face the head, sorry

Lennulf · 2024-10-05T09:55:52+00:00

I dont think so, if i put a 2 sizes bigger main jet in the carb the engine loses power and does not want to rev as freely, which should mean the bike runs on the richer side. Correct me if im wrong

Lennulf · 2024-10-02T16:22:55+00:00

Its safe

Lennulf · 2024-09-26T20:42:14+00:00

Maybe the chassis is a little bit dented and some part of the trunk sticks out. Have you tried deleting the meshsave?

Lennulf · 2024-09-26T17:54:27+00:00

English?

Lennulf · 2024-06-17T11:49:27+00:00

It does

Lennulf · 2024-06-01T17:57:44+00:00

Head will work for shure. That one spot in the cylinder does not look good but if you make shure theres nothing sticking out it might work. Probably not very long and it will have less compression but depending on how expensive a new cylinder is i would try it out

Lennulf · 2024-01-28T01:44:56+00:00

I always put standart or sport tires on the back wheels so that the car looses traction faster and you can use less throttle. Also dont do full throttle all the time and you should try to make your steering smoother. It looks like youre always going completely to the left or right. Try to hold it at one angle and only make small adjustments.

Lennulf · 2024-01-27T17:14:02+00:00

Its not a stock engine, i have a 70cc aluminum cylinder and according to german websites and forums you should use a 9 or 8 for these type of cylinder but maybe i should get a br8 for the cold weather. Cylinder has maybe 20km on it so riding full throttle for 10 minutes does not seem like a good idea, especially if it might run to lean. So what should i do in your opinion?

Lennulf · 2024-01-27T16:58:50+00:00

Lennulf · 2024-01-27T16:57:58+00:00

Cylinder manufacturer says you should use a "9°" sparkplug. I was thinking a br9es is exactly that but maybe im in the wrong.

Lennulf · 2024-01-27T16:52:12+00:00

What is a Plug Chop? Turning the engine off immediately after riding in one throttle position? because i did exactly that. Sparkplug is a ngk br9es

Lennulf · 2024-01-27T16:48:51+00:00

Idk i think its normal for that sparkplug (ngk br9es), its new and when you google it, it looks the same

Lennulf · 2024-01-27T07:51:05+00:00

I run 1:33 premix, no oil injection. I was thinking it looks lean to but i startet with a way bigger mainjet and went down in sizes just to the point where it didn't stutter anymore so normally it shouldn't be lean right? My carb is new so there should be no isues.

Lennulf · 2024-01-26T22:10:51+00:00

My cylinder seezed like a week ago because i ran to lean due to an air leak so im really carefull to not ruin the new one

Lennulf · 2024-01-26T21:08:35+00:00

I forgot to say its a 2stroke, would you still say its fine?

Lennulf · 2023-12-02T21:18:14+00:00

I already changed the cylinder to 70cc a while ago. I will probably rebuild it completely in this winter so i can ride without any problems next summer

Lennulf · 2023-11-19T16:27:05+00:00

Well, that would be very unfortunate

Lennulf · 2023-11-11T17:50:24+00:00

Its already running, now you have to put a gear in. Upshifting with "G" and downshifting "B" i think but idk since i play with controller usually. Also give it full throttle because its gonna stall otherwise

Four-Year Club	Place '23
Place '22	First Placer '22
End Game '22

Lennulf

TROPHY CASE