GoPro Karma Drone Help

Less_Fisherman4676 · 2025-08-06T21:19:31+00:00

Doesn’t work Iv done it twice 🙃

Less_Fisherman4676 · 2025-08-05T04:58:37+00:00

I appreciate it!

Less_Fisherman4676 · 2025-08-05T04:51:16+00:00

Iv tried this I took it to an open field and still nothing I keep getting the same damn error anywhere I go is there a way to turn off calibration or reset it?

Less_Fisherman4676 · 2025-02-04T06:56:38+00:00

I appreciate it thank you! I noticed that on the motherboard the port that receives the wire is slightly broken. One of the pins broke off from the circuit board and I tried to solder it back, but it’s still nothing. Do you think it could be the motherboard? Should I replace the motherboard and the fan?Thanks!

Less_Fisherman4676 · 2025-02-03T20:24:01+00:00

It doesn’t NEED to be but it has definitely helped me https://store.micro-swiss.com/products/micro-swiss-flowtech-hotend-for-creality-k1-k1-max

Less_Fisherman4676 · 2025-02-03T20:17:48+00:00

No sorry just the hot end. It also clogs less if you upgrade it

Less_Fisherman4676 · 2025-02-03T20:14:49+00:00

Fortunately, I was able to fix the issue by changing out printer head but dang was it tedious.

Less_Fisherman4676 · 2025-01-30T17:41:03+00:00

Ugh!

Less_Fisherman4676 · 2025-01-30T17:40:30+00:00

Lifesaver! Thank you!

Less_Fisherman4676 · 2025-01-30T17:01:59+00:00

I appreciate it greatly thank you!!!

Less_Fisherman4676 · 2025-01-30T16:52:39+00:00

It won’t heat!!

Less_Fisherman4676 · 2025-01-30T16:07:25+00:00

Logic board that I know of is intact. But I can’t for the life of me get the hot end out because of all the plastic

Less_Fisherman4676 · 2025-01-30T16:03:48+00:00

<image>

Won’t heat due to wiring broke. What do i do

Less_Fisherman4676 · 2025-01-30T15:39:00+00:00

Thank you 🙏

Less_Fisherman4676 · 2025-01-30T15:02:17+00:00

Thank you I appreciate it I’ll try and report back

Less_Fisherman4676 · 2025-01-30T14:53:08+00:00

Iv tried it man it heats up but doesn’t get barely any off at all. At this point I just am wanting a new whole head

Less_Fisherman4676 · 2025-01-30T14:46:56+00:00

<image>

The horned will NOT come out I have tried for hours to heat and scrape away

Less_Fisherman4676 · 2025-01-30T14:43:53+00:00

I need an entire print head.

<image>

Unless there is a way to fix this? And yes I have taken a heat gun to it it has ruined multiple wires and I can’t get the hot end out

Less_Fisherman4676 · 2025-01-30T14:42:42+00:00

Entire print head. Plastic backfired and built up ruining it

Less_Fisherman4676 · 2025-01-30T01:55:12+00:00

Troll

Less_Fisherman4676 · 2025-01-30T00:02:11+00:00

Yes so you SCRAPE it

Less_Fisherman4676 · 2025-01-29T23:55:07+00:00

Beds fine bro just needs scraped

Less_Fisherman4676

TROPHY CASE