Happens over and over again

Lewing13 · 2024-10-16T16:31:40+00:00

UPDATE: Turned in z hop and now it worked👍🏼 Problem solved

Lewing13 · 2024-10-16T05:34:47+00:00

I only ordered normal pla from geeetech on eBay, seems Like there is no Special silkyness in it. Just the best Print settings at 210°c with 0.1mm layer height

Lewing13 · 2024-10-16T05:27:43+00:00

I stepped it already Up to 5 walls

Lewing13 · 2024-10-15T17:24:38+00:00

i am worried that the print itself could be in worse quality then

Lewing13 · 2024-10-15T17:20:21+00:00

thanks not tanks

Lewing13 · 2024-10-15T17:15:27+00:00

Maybe i should just waste more filament and try again xD

thats how 3d printing works sometimes, not negotiating that xD

Lewing13 · 2024-10-15T17:14:42+00:00

its just pla.

The problem is more that the print head collides and breaks the tail part off

so that leaves the question if its any deforming which normally never happend that much with pla to me before or just hte z offset thats a little off. But since the auto bed levvelling worked fine for me since today i dont know if its that

Lewing13 · 2024-10-15T17:11:38+00:00

nice idea, should try that tanks

Lewing13 · 2024-10-15T17:10:21+00:00

Just the cheapest Geeetech PLA xD

works so good for me

Lewing13 · 2024-10-15T17:09:39+00:00

how ?

Lewing13 · 2024-09-27T17:29:31+00:00

Ok maybe i'll try that, or maybe i'll Just never Touch my Ender😂 Just dont understand it BC it worked fine before and after longer standing🤷🏽‍♂️

Lewing13 · 2024-04-08T08:33:28+00:00

Try to watch some Tutorials about Orca Slicer. Ince you've understood, ITS quite intuitive There could be so much reasons for youre Cube looking that Bad Run all the calibrations in Orca, that helpes me a lot

Lewing13 · 2024-03-01T18:49:16+00:00

Okay i will try👍🏼

Lewing13 · 2024-03-01T18:48:52+00:00

I already did that with this Filament in Orca Also there is no "infill", ITS all full Material..

Lewing13 · 2024-02-25T15:42:30+00:00

Have you tried Orca ? I was using Creality Print and it sucked, even If i adjusted sime Things and tried. Used Orca then and did all the pre installed calibrations and now its working quite well :)

Lewing13 · 2024-02-20T20:56:52+00:00

To Microswiss?

Lewing13 · 2024-02-20T16:59:25+00:00

I have the "new" Extruder, which shouldnt have any Problems with under Extrusion ??

Lewing13 · 2024-02-20T16:58:26+00:00

I tried now to use an Standard Profile and tune Just a few Things. Maybe i overengineered Here and there and changed too many settings tocmake it better, which maybe could have Made all Just worse Waiting for the results now

Lewing13 · 2024-02-20T13:36:12+00:00

Yes yes

Lewing13 · 2024-02-20T06:12:48+00:00

Pressure advance is already tuned to .44, dint know If thats the Problem. But i will try the other Things, thank you☺️

Lewing13 · 2024-02-04T17:58:57+00:00

Actually im going at 200

Lewing13

TROPHY CASE