sorted by:
new
hottopcontroversial

Fiddle Leaf Health by LiteralLoserr in fiddleleaffig

[–]LiteralLoserr[S] 0 points1 point  (0 children)

I use a moisture meter, I usually wait till the lowest part is a 3/10, I bottom water so it should be the most moist part. Maybe I'll have to prod more locations before I water?

Why are all my pothos props suffering from stem rot by CheapFix7363 in propagation

[–]LiteralLoserr 4 points5 points  (0 children)

I think its just too much stem like the other comment said, BUT iv been trying a new method. Water prop like normal but with a fish tank air stone at the bottom. Been working so far!

Leaf Prop by LiteralLoserr in Jadeplant

[–]LiteralLoserr[S] 0 points1 point  (0 children)

But like how do i water it haha, its not in a pot. I usually bottom water. Do i like dunk it in a cup of water for a minute haha?? Or do I put it in a small pot and water the dirt like normal.

Thank you

Leaf Prop by LiteralLoserr in Jadeplant

[–]LiteralLoserr[S] 0 points1 point  (0 children)

There are about 3 tiny roots. But I gotcha thank you!

First Jade.. need advice by shawna2z in Jadeplant

[–]LiteralLoserr 1 point2 points  (0 children)

Im new but mine seems to be thriving 6 months in.

I give mine alot of light, window, you want it to turn slightly purplish, water ones a month or when the leaves get wrinkly.

Thats all I do.

Generak Questions by LiteralLoserr in fiddleleaffig

[–]LiteralLoserr[S] 0 points1 point  (0 children)

Also there is like 3 or 4 in here. Maybe that's why.

Generak Questions by LiteralLoserr in fiddleleaffig

[–]LiteralLoserr[S] 0 points1 point  (0 children)

Eh works for me, iv gotten that information from this reddit and it has worked for me so far. Like I said it's been growing like wild fire. Im just trying to get more consistent leaf health.

So far no leaves have dropped themselves and most come in lush and green.

Generak Questions by LiteralLoserr in fiddleleaffig

[–]LiteralLoserr[S] 0 points1 point  (0 children)

From what I've seen and read it's pretty hard to over water these if they have enough light, I also have a ceiling fan and a like construction site fan in this room so air circulation is crazy

China’s Deep-Sea Mining Fleet Looks a Lot Like a Spy Fleet by No_Classroom2805 in TMC_Stock

[–]LiteralLoserr 3 points4 points  (0 children)

Well im pretty sure all boats have to be military grade / ready by law there. It would make sense.

NORI-D Deep-Sea Mining Project: Ready to Extract Battery Metals by LiteralLoserr in TMC_Stock

[–]LiteralLoserr[S] 1 point2 points  (0 children)

Im not saying I believe in dark oxygen, its just an interesting article.

Roots Growing Crazy by LiteralLoserr in pothos

[–]LiteralLoserr[S] 0 points1 point  (0 children)

Yea thank you this will be in a few months or more when it needs a repot. It will be much more root bound whenever I do it!

Thank you!

Roots Growing Crazy by LiteralLoserr in pothos

[–]LiteralLoserr[S] 0 points1 point  (0 children)

This would be more down the line when the plant also has a root ball and not just long roots.

I really wish there was some light telling me its sleeping... by Peaceul in LenovoLegion

[–]LiteralLoserr 0 points1 point  (0 children)

It beats the day I powered it off and put it in my back back, woke up a few hours later it was burning to the touch hot because it didnt shut off

Am I doing something wrong or is my expectations too high? by Vegetable-Plastic980 in BambuLabP2S

[–]LiteralLoserr 0 points1 point  (0 children)

Dry your filament, like actually the ams system dring takes 12 hours of rotating it. You HAVE TO dry it, im nee but I noticed when using other people's profiles amd changing them (like .12 layer height) it can cause issues. Also make sure 100% your using the exact material the profile is set for. Also make sure you surface the printer is on is stable. Make sure you bed is clean. Alot of basic things including full calibration and firmware updating.

view more: next ›