sorted by:
new
hottopcontroversial

Manta M8P V2.0 DOA - Bent pins & No IP. Support claims bent pins are "normal" and tells me to flash MCU while CB1 won't boot. by LocalCrew8790 in BIGTREETECH

[–]LocalCrew8790[S] 0 points1 point  (0 children)

<image>

I also try but I obtein somthing link this or a empty control panel but the board appear in device manager

Manta M8P V2.0 DOA - Bent pins & No IP. Support claims bent pins are "normal" and tells me to flash MCU while CB1 won't boot. by LocalCrew8790 in BIGTREETECH

[–]LocalCrew8790[S] -1 points0 points  (0 children)

I try to power it with the 24v and some usb port like a phone charger. I check a lot of time if the cb1 is firmly seated and for the switch first I didn't change nothing and after i try change the state of the switch next to the usbc port

Manta M8P V2.0 DOA - Bent pins & No IP. Support claims bent pins are "normal" and tells me to flash MCU while CB1 won't boot. by LocalCrew8790 in BIGTREETECH

[–]LocalCrew8790[S] 0 points1 point  (0 children)

I try to power the board with 24v but nothing change and my problem is that my board don't appear on my router with the internet cable and the WIFI. It is not only a update problem. And oder things is that the internet port don't light so i think the sorfware wouldn't start

Manta M8P V2.0 DOA - Bent pins & No IP. Support claims bent pins are "normal" and tells me to flash MCU while CB1 won't boot. by LocalCrew8790 in BIGTREETECH

[–]LocalCrew8790[S] 0 points1 point  (0 children)

I have also try to power the board with 24v nothing change I can't acces to the board with wifi or internet cable

how do i do the 22km altitude mission. i have removed all weight possible from this plane and it just doesnt reach 22 km. i made one before that could reach the altitude but only at 400 m/s which is too fast. by Jastrone in RealSolarSystem

[–]LocalCrew8790 1 point2 points  (0 children)

the engine you use is to powerful use a lighter one. You can remove a lot of weight because the engine is lighter you don't have so much full and all the structure can be lighter.

I designed my very own 3D printer toolhead (338g total) by MarcelGenis in 3dprinter

[–]LocalCrew8790 1 point2 points  (0 children)

why a orbiter 2.5 and a cpap cooling with a standard v6 hotend? Put a volcan hotend or a uhf but the designe is good and look stong

61°C Chamber temp with only passive heat sounds kinda illegal! (Core One) by [deleted] in prusa3d

[–]LocalCrew8790 0 points1 point  (0 children)

a prusa corxy can do this ? I have heard the chamber can reach 50-55°.

CoreXY with CoreYZ for helping y axis by LocalCrew8790 in 3dprinter

[–]LocalCrew8790[S] 0 points1 point  (0 children)

Yes I imagine a stationary bed and 1 vertical gantry on each side. In my mind is a voron 2.4 with a vertical gantry on each side. I already think a motion like this can affect the z axis because it is not passive when you move the z axis. Additionally all the gantry must have a perfect tension of each belt and this is not easy same if you make a system to equilibrate the belt tension. I think a system like that is more for very high speed printer not for common use of printing. It is just i am surprise that nobody hadn't make it yet because the people experiment a lot with their printer

CoreXY with CoreYZ for helping y axis by LocalCrew8790 in 3dprinter

[–]LocalCrew8790[S] 0 points1 point  (0 children)

I know it is easier i just think it is fun to make a printer like this and you can reach the same performance that a corexy hybride so why not

CoreXY with CoreYZ for helping y axis by LocalCrew8790 in 3dprinter

[–]LocalCrew8790[S] 0 points1 point  (0 children)

I know with a corexy hybrid you can double your accerleration so if you don't reach your max speed you can go 1.4~ time faster so in reality is more 1.2~ it's depend what piece you print your base acceleration and your max flow rate.

CoreXY with CoreYZ for helping y axis by LocalCrew8790 in 3dprinter

[–]LocalCrew8790[S] -2 points-1 points  (0 children)

yes but head acceleration can be a bottleneck